
A ground robot is a traction load with a computer attached. That single sentence explains most of the confusion in unmanned ground vehicle (UGV) power design. The pack must deliver motor peak current on a slope, keep a compute and communications bus alive during a long watch, and survive being carried, dropped and recharged from a vehicle alternator. The energy that moves the platform and the energy that keeps it thinking are different problems, and they scale differently across the five UGV classes. This paper sets out those classes and the four load buckets behind them, then states plainly where sealed NiMH fits and where it does not.
| Class | Representative platform | Mass | Drive power | Battery architecture | Endurance |
|---|---|---|---|---|---|
| Man-portable EOD / reconnaissance | PackBot 510, TALON | 10–60 kg | 0.3–1.5 kW peak | One or two BB-2590-class packs, hot-swap | 4–12 h |
| Medium tactical | Wheeled or tracked 100–300 kg | 100–300 kg | 2–6 kW peak | 24–48 V string, 2–8 kWh | 6–12 h |
| Large logistic | THeMIS-class | 1,000–2,000 kg | 10–30 kW peak | Diesel-electric hybrid; 24–48 V buffer | 15 h diesel / 1.5 h electric |
| Armed / weaponised | MAARS-class | 300–500 kg | 5–15 kW peak | 24–48 V string with weapon bus | 8–24 h depending on fit |
| Micro / throwable | Sub-5 kg sensor robots | < 5 kg | < 100 W | Single 3S–6S pack | 1–3 h |
The table is a planning frame, not a product registry. Its purpose is to show that "UGV battery" spans two orders of magnitude in power and three in mass. A specification written for one class should never be reused for another without re-deriving the load list.
| Bucket | Typical consumers | Duty shape | Energy share | Sizing consequence |
|---|---|---|---|---|
| Traction | Drive motors, steering actuators | Highly variable, peaky | 40–70 % while moving | Sets peak current, fuse and connector rating |
| Manipulation | Arm joints, gripper, pan-tilt | Bursts of a few seconds | 10–25 % while working | Sets voltage sag tolerance |
| Compute and perception | Onboard computer, cameras, LiDAR, GPU | Continuous while awake | 10–30 % | Sets average energy and thermal load |
| Communications | Radio, mesh node, video link | Continuous, higher when transmitting | 5–15 % | Sets idle drain and antenna isolation |
A fifth bucket, standby or watch, is often omitted: the robot is powered but not moving, with compute in a low-power state and the radio listening. On a platform that spends most of a shift waiting, watch energy can exceed traction energy. The load audit should therefore report both a "moving hour" and a "watching hour" profile, and size the pack for the mix that the mission actually specifies.
| Payload | Typical power | Duty | Effect on pack sizing |
|---|---|---|---|
| Onboard computer (CPU only) | 15–40 W | Continuous awake | Baseline hotel load |
| GPU or vision accelerator | 30–120 W | Bursty during perception | Raises average and creates thermal peaks |
| Cameras and LiDAR | 10–40 W | Continuous | Small but never sleeps |
| Mesh radio or video link | 5–30 W | Continuous; higher on transmit | Dominates long watch periods |
| Arm and gripper electronics | 5–20 W idle; 100–500 W working | Bursty | Voltage sag during simultaneous drive and arm |
| Lighting and warning | 5–20 W | Night operations | Easy to omit from the audit |
Compute is the new hotel load of ground robotics. A platform that idles with perception running can consume more in a six-hour watch than in an hour of driving, and the pack sees that load as a steady, warm drain. If the payload is expected to run while the robot is stationary for most of a shift, a separate payload pack is often the cleanest architecture.
| Condition | Approximate tractive force | Power at 1 m/s | Duration | Design implication |
|---|---|---|---|---|
| Flat, hard surface, 14 kg platform | 30–60 N | 30–60 W | Continuous | Average load is modest |
| 10° slope, same platform | 60–100 N | 60–100 W | Minutes | Thermal margin in the motor driver |
| 30° slope or stair climb | 150–250 N | 150–250 W | Tens of seconds | Peak current and pack internal resistance |
| Obstacle or stall | 300–500 N | Current-limited | Seconds until protection | Fuse curve and PCM over-current trip |
The stall row is the important one. A drive motor that stalls at 20 A per side on a 24 V bus draws 40 A, and a dual-pack architecture shares it. The pack's continuous rating may be 10 A, but its pulse rating must cover the stall for the time the controller takes to fold back. This is a protection-coordination problem, not a capacity problem, and it is the reason a pack that performs well on a bench can nuisance-trip on a kerb.
| Platform | Mass | Battery | Endurance | Notes |
|---|---|---|---|---|
| PackBot 510 | 14.3 kg | Two BB-2590 lithium packs | 4–8 h | 9.3 km/h; climbs 60°; radio range about 1,000 m; optional 6 kg power pod extends to about 12 h |
| TALON | About 52 kg | Lead-acid standard; lithium option | 8.5 h normal; 7 days standby | Two lead-acid batteries give about 2 h each; lithium option adds about 4.6 h |
| THeMIS | 1,630 kg | Diesel-electric hybrid; lead-acid or lithium buffer | 15 h diesel; 1.5 h pure electric | Payload several hundred kg; hybrid removes the pure-battery endurance constraint |
| MAARS | About 350 kg | Lithium pack | Up to 312 h on battery, 1 week sleep | Manufacturer figure; mission-dependent |
Two lessons emerge. First, the man-portable class uses dual small packs and hot-swap, because endurance is extended by carrying spares, not by making one pack larger. Second, the large class moves to hybridisation, because no practical battery at 1.6 tonnes gives a full working day. Between those two, the medium class is where pack energy and pack mass trade most directly.
| Property | BB-2590/U (lithium) | BB-390/U (NiMH) |
|---|---|---|
| Chemistry | Lithium-ion | Nickel-metal-hydride |
| Voltage / capacity | 14.4 V 20 Ah or 28.8 V 10 Ah | 12.0 V 9.0 Ah or 24.0 V 4.5 Ah |
| Energy | About 288 Wh | About 108 Wh |
| Mass | About 3.5 kg | Comparable form factor, lower energy |
| Temperature | −40 to +60 °C (operating range claimed) | Discharge to about −20 °C; charge above 0 °C |
| Communication | SMBus, 6-pin SC-C-179495 connector | Same family of military battery interfaces, simpler monitoring |
| Cycle life | Several hundred to 1,000+ depending on DoD | About 500 deep cycles |
| Role today | Standard main pack for man-portable UGV | Legacy, training, depot, auxiliary |
The BB-390/U is the honest anchor for NiMH in the UGV world. It exists, it is dual-voltage, it fits the same logistics family, and it is about 108 Wh rather than 288 Wh. That energy gap is the whole story: the nickel pack is not a drop-in replacement for a 2590 lithium pack on an endurance-critical platform. It is a drop-in replacement where the mission can accept roughly one-third of the energy, or where the platform was designed around it.
| Application | Why NiMH works | Constraint to respect | Evidence anchor |
|---|---|---|---|
| Legacy fleet sustainment | Original equipment designed for BB-390/U voltage and energy | Do not promise 2590-class endurance | BB-390/U dual-voltage 108 Wh specification |
| Training and simulation robots | Low cost, tolerant charging, no lithium transport paperwork | Shallower depth of discharge; more frequent charging | UN 3496 transport route |
| Depot and garrison charging | Simple 0.1C charge, no balancing electronics | Charge time 14–16 h; ventilation required | IEC 61951-2 charge methods |
| Auxiliary and payload packs | Powers sensors or a secondary radio independent of traction | Isolated DC-DC; separate return path | Dual-bus architecture practice |
| Target and test platforms | Cheap, robust, replaceable after abuse | Not for live-fire or high-shock use without test | IEC 62133-1 abuse tests |
Each row shares a property: the platform does not depend on the highest energy density. The moment a requirement says "8 hours of continuous mobility at 14 kg", the nickel pack loses to lithium on mass and the honest answer is to say so. The moment a requirement says "keep the legacy TALON running in training for another two years", the nickel pack is a sensible sustainment answer.
| UGV class | Main pack chemistry | NiMH fit | Reason |
|---|---|---|---|
| Man-portable EOD | Lithium (BB-2590 family) | Legacy sustainment only | Energy per kilogram decides endurance |
| Medium tactical | Lithium string | Auxiliary pack, depot, training | Traction energy too high for nickel at practical mass |
| Large logistic | Diesel-electric hybrid | Buffer or start battery, not traction | Hybrid removes the battery-energy constraint |
| Armed / weaponised | Lithium string | Ancillary and training | Weapon bus and mission endurance favour lithium |
| Micro / throwable | Small lithium or NiMH | Genuine fit at small energy | Low energy, low cost, tolerant charging |
The matrix is a fit judgement, not a market forecast. It says where a nickel pack can be sold honestly and where it cannot. A supplier who claims the last column for every row will lose technical credibility on the first platform integration review.


Modern man-portable and medium UGVs use lithium main packs, typically BB-2590-class or custom strings. Nickel-metal-hydride appears in legacy fleets, training platforms, auxiliary packs and depot equipment, not as the endurance-critical main pack.
Manufacturer figures for the PackBot 510 are 4–8 hours on two BB-2590 packs, extended to about 12 hours with the optional power pod. Actual endurance depends on speed, slope, payload and radio duty cycle.
Because a 1.6-tonne platform needs far more energy than a practical battery can carry for a full shift. The THeMIS claims about 15 hours on diesel and 1.5 hours on battery alone; the hybrid architecture lets the engine run at an efficient point and the battery handle peaks.
Only with the right architecture: inrush limiting, ORing diodes or ideal-diode controllers, a supervisor that sequences the swap, and connectors rated for the make/break current. A connector alone does not make a pack hot-swappable.
24 V or 48 V are the common buses. 24 V suits man-portable and small medium platforms; 48 V reduces current for the same power and is preferred as traction power rises. The choice affects connector, fuse and DC-DC design more than it affects the cells.
A lithium pack does, without qualification. A NiMH pack benefits from cell-group voltage monitoring, temperature sensing and a low-voltage disconnect, but it does not need the same balancing electronics. The protection functions are still necessary; the balancing function is not.
PackBot 510 published specifications (14.3 kg, dual BB-2590 lithium, 4–8 h, 9.3 km/h, 60° climb, 1,000 m radio range, 6 kg power pod to about 12 h); TALON published specifications (about 52 kg, lead-acid standard, 8.5 h normal, 7 days standby, lithium option adds about 4.57 h); THeMIS published specifications (1,630 kg, diesel-electric hybrid, 15 h diesel / 1.5 h electric, lead-acid or lithium buffer); MAARS published battery endurance figure (up to 312 h, one week sleep); BB-2590/U specification (14.4 V 20 Ah / 28.8 V 10 Ah, about 288 Wh, −40 to +60 °C, SMBus, 6-pin SC-C-179495); BB-390/U specification (12 V 9.0 Ah / 24 V 4.5 Ah, about 108 Wh, about 500 deep cycles, discharge to about −20 °C); IEC 61951-2 and IEC 62133-1; UN 3496. Endurance figures are manufacturer claims and mission-dependent.
Paper B — Selecting and sizing sealed NiMH packs for unmanned ground vehicle support: the load audit, cell configuration, derating, hot-swap architecture and charging. Paper C covers test and certification, including shock, vibration, ingress and transport.
Weijiang Power — sealed NiMH cells and packs for industrial support equipment.
OEM and custom configurations, with honest chemistry boundaries. Visit our product range or browse the full technical series.
Buyer fact sheet
| Legal entity | Shenzhen Weijiang Battery Co., Ltd., trading as Weijiang Power |
| Founded | 2010, 16 years of NiMH battery manufacturing |
| Factory | Huizhou Shenzhou Super Power Technology Co., Ltd., Zhongkai High-tech Zone, Huizhou, Guangdong; 12,000 m2, 4 workshops |
| Capacity | 200,000 NiMH cells per day; 200+ staff including 11-20 R&D engineers and 10 QC inspectors |
| Product range | NiMH cells A, AA, AAA, SC, C, D, 9V, F, Sub-C, 4/5AA, 2/3A; custom NiMH packs; chargers; button and alkaline cells |
| Certifications | CE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001:2015, ISO 14001, IATF 16949, IEC 62321, MSDS, UL, IEC 62133; 16 patents; UN38.3 applies only to lithium packs |
| Markets | 60+ countries, focus on Europe and the United States |
| Order terms | No strict MOQ on standard stock; OEM samples 7-15 days; standard production 7-12 days; custom packs 15-25 days |
| Medical NiMH | Medical NiMH battery page |
Who is Weijiang Power?
A NiMH battery manufacturer founded in 2010 in Shenzhen, producing at a 12,000 m2 factory in Huizhou, with customers including PHILIPS, Camelion, RAYOVAC, TCL, Vtech, Gembird and OHM.
What can Weijiang Power supply?
Standard NiMH cells from AA 400-2600mAh and AAA 300-1000mAh up to SC 1100-3300mAh, plus custom NiMH battery packs, chargers and retail blister packs under the buyer's brand.
Which certificates are available for EU and US buyers?
CE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001, ISO 14001, IATF 16949, IEC 62321, MSDS, UL and IEC 62133, with 16 patents; UN38.3 applies only to lithium packs.
What is the minimum order and lead time?
Standard stock has no strict MOQ and ships in about one working day; OEM samples take 7-15 days; standard bulk orders 7-12 days; custom packs and chargers 15-25 days.
How do I get a sample or a quote?
Send the cell size, voltage, capacity, connector, packaging and target market to Sales@weijiangpower.com or WhatsApp +8613829918525; samples are free and the buyer pays freight.
Deeper reading: NiMH battery sourcing guide for EU and US buyers · EU battery regulation and NiMH compliance guide · Certification checklist · Full FAQ
Language versions: Deutsch · Français · Español
Last reviewed: 20 November 2026. Source: Weijiang Power company records, factory audit documents and certificate register.