Nov.2026 20
Views: 96
Testing and Certifying Sealed NiMH Packs for Sonar and Underwater Support Equipment: IEC 61951-2, IEC 62133-1, Ingress and Pressure, Environmental, EMC and UN 3496
Introduction
Paper C: testing and certification for NiMH sonar support packs. The four-level programme, IEC 61951-2 performance, IEC 62133-1 abuse tests, the difference between IP codes and depth ratings, hydrostatic pressure at 6,000 m, environmental sequences, EMC with motors running, and the UN 3496 transport route.
Details

Testing and certifying sealed NiMH packs for sonar and underwater support equipment

"Waterproof to 6,000 metres" is not a property of a battery pack. It is a property of a housing, a connector and a pressure boundary, proven by a test that the supplier can name. Sonar and underwater support equipment attracts some of the most confident and least supported claims in the battery business: IP68 without a pressure test, "subsea-ready" packs that have never seen a hyperbaric chamber, and UN 38.3 certificates attached to nickel-metal-hydride packs that do not travel under the lithium entries at all. This paper sets out the test pyramid, the standards that actually apply, and the acceptance criteria that turn a claim into evidence.

Key facts at a glance

  • Three levels, three different questions. Cell tests prove the chemistry; pack tests prove the assembly and protection; system tests prove the installation. A pack certificate cannot answer a system question.
  • IEC 61951-2 is the performance standard for sealed NiMH. It covers capacity, cycle endurance, charge retention and overcharge behaviour, and it is not a safety certificate.
  • IEC 62133-1 is the nickel-system safety standard. It covers abuse tolerance at cell and pack level, and it is deliberately separate from IEC 62133-2 for lithium.
  • IP codes are not pressure ratings. The second digit describes water ingress under defined conditions, not hydrostatic pressure at depth. A depth rating needs a pressure test and a stated safety factor.
  • NiMH travels under UN 3496. No UN 38.3 test summary is required, and applying the lithium entries to a nickel pack is a paperwork error that can stop a shipment.

The three-level test pyramid

Level Object under test Standards Question answered Who usually owns it
Cell Single sealed NiMH cell IEC 61951-2, IEC 62133-1 Does the chemistry meet its claimed capacity and abuse tolerance? Cell manufacturer
Pack Cells, interconnect, PCM, fuse, thermistor, housing IEC 62133-1 pack tests, IEC 60529, IEC 60068-2 Does the assembly survive the environment and the load? Pack assembler
System Pack installed in the equipment or housing IEC 62368-1, product-specific standard, EMC Does the installation remain safe and functional in service? Equipment integrator

The pyramid is not a hierarchy of importance; it is a division of responsibility. A cell certificate quoted for a pack is as incomplete as a pack certificate quoted for an installed system. Procurement documents should state which level each certificate covers and who is accountable for the gaps.

IEC 61951-2: performance, not safety

IEC 61951-2 covers sealed nickel-metal-hydride cells for portable applications. Its tests are designed to establish that a cell performs as declared, not that it is safe under abuse. The table lists the tests most often relevant to a support-pack specification.

Test What it does Typical acceptance Why it matters for a sonar support pack
Rated capacity Discharge at the declared rate to the cut-off voltage ≥ declared capacity at 0.2C, 20 °C Establishes the basis for every derating calculation
Cycle endurance Repeated charge/discharge to a defined depth Declared cycles to 80 % capacity A deck test set may see 300 cycles a year
Charge retention Store charged, then discharge Declared retention after 28 days A moored node may sit uncharged for a month
Overcharge Continue charging at a defined rate No leakage, no rupture, capacity within tolerance A standby pack may be left on trickle
High-rate discharge Discharge above the nominal rate Declared voltage and capacity A USBL beacon draws a short 2–4 A burst
Low-temperature discharge Discharge at a declared cold temperature Declared percentage of room-temperature capacity Deck work in winter and cold stores

A common error is to quote a cycle-endurance figure measured at 100 percent depth of discharge for a pack that will actually run at 30 percent depth. The shallower cycle life is longer, but it must be measured or derived from the cell datasheet, not assumed. The other common error is to quote room-temperature capacity for a pack that will spend its life in an unheated deck locker.

IEC 62133-1: abuse tolerance

Test Condition Acceptance criterion Typical failure mode
External short circuit Short the terminals at a defined resistance and temperature No fire, no explosion, no leakage Separator melt or venting at the weld
Impact Drop a defined mass onto the cell or pack No fire, no explosion Internal short at the electrode edge
Drop Free fall onto a hard surface No fire, no explosion, no loss of function Cracked interconnect or displaced PCM
Thermal abuse Soak at a defined elevated temperature No fire, no explosion Vent opening and electrolyte loss
Overcharge Charge at a defined rate beyond full charge No fire, no explosion Positive-electrode swelling and venting
Forced discharge Drive a cell into reverse polarity No fire, no explosion Reverse-cell heating in a series string

For a 20S pack, the forced-discharge test is the one that exposes a weak cell: if one cell reaches reversal before the others, the string drives current through it and the heat is localized. A pack-level PCM that senses cell group voltage, not just pack voltage, is the mitigation. The test is performed on cells in the standard; the pack designer has to reproduce the protection behaviour at string level.

Ingress, pressure and the difference between them

IEC 60529 defines the IP code. The first digit is solids, the second is water. For underwater support equipment the relevant second digits are 5 (jet), 6 (strong jet), 7 (temporary immersion), 8 (continuous immersion) and 9K (high-temperature, high-pressure jet cleaning). None of them is a depth rating.

Code Test condition What it proves What it does not prove
IP54 Dust protected, splashing water Deck and workshop use Rain-driven immersion
IP65 Dust tight, water jets Hose-down and heavy weather on deck Immersion
IP67 Dust tight, immersion at 1 m for 30 min Temporary immersion, shallow Pressure at 10 m or more
IP68 Continuous immersion, depth and duration by agreement Only what the manufacturer declares A depth rating without a stated depth and test
IP69K High-pressure, high-temperature jet Clean-down, not depth Hydrostatic pressure

Hydrostatic pressure is straightforward arithmetic: P = ρ g h. At 10 m, fresh water gives about 0.98 bar above ambient; at 100 m about 9.8 bar; at 6,000 m about 588 bar. A pack declared for 6,000 m therefore needs a housing tested at roughly 600 bar, usually with a safety factor of 1.5 on the design pressure. An IP68 test at 1 m for 30 minutes is not evidence for any of those numbers.

There is a second, subtler issue: a sealed pack that is potted or encapsulated cannot be inspected after a pressure cycle. A housing that is opened for cell replacement needs a reusable, tested seal, and the connector must be pressure-rated as part of the boundary. The weak point in most "subsea" packs is not the cell; it is the connector and the cable gland.

Environmental sequence

Stress Standard / method Typical level for a deck pack Read-back after test
Cold IEC 60068-2-1; MIL-STD-810 Method 501 −20 °C soak, operational check Capacity, voltage sag at rated current
Dry heat IEC 60068-2-2; MIL-STD-810 Method 501 +55 °C soak Capacity, leakage, case deformation
Damp heat IEC 60068-2-30; MIL-STD-810 Method 507 40 °C, 93 % RH, cyclic Insulation resistance, corrosion
Vibration IEC 60068-2-6; MIL-STD-810 Method 514 10–55 Hz, 1 g sweep; or application profile Tab welds, connector retention
Shock IEC 60068-2-27; MIL-STD-810 Method 516 15 g, 11 ms, three axes Cell displacement, fuse integrity
Salt mist IEC 60068-2-52; ASTM B117 48–96 h neutral salt fog Terminal corrosion, seal integrity
Sand and dust IEC 60529 IP5X/IP6X; MIL-STD-810 Method 510 Dust chamber Connector contamination

The sequence matters as much as the levels. A pack that passes cold, then damp heat, then vibration is not the same as one that passes each test on a fresh sample. For a deck product, the realistic sequence is cold → damp heat → vibration → salt mist, with a functional check after each step and a full capacity check at the end.

EMC: the pack is part of the system

Test Standard Why a battery pack is involved
Electrostatic discharge IEC 61000-4-2; MIL-STD-461 CS114/RS103 A charged operator touching the connector can inject current into the PCM
Radiated immunity IEC 61000-4-3 Radio equipment on the same deck couples into the pack leads
Burst / surge IEC 61000-4-4 / -4-5 Relay and motor switching on the same 24 V bus
Conducted emissions EN 55011 / CISPR 11; MIL-STD-461 CE102 The charger is often the noisy part, not the pack
Radiated emissions EN 55011; MIL-STD-461 RE102 A switching PCM can radiate above the limit

A passive NiMH pack is electrically quiet; the charger and the PCM are not. Test the pack with the charger that will be used, and test the installation with the cable length that will be used. A ferrite on a one-metre bench cable is not evidence for a ten-metre deck cable.

Transport: UN 3496 and the nickel route

Mode Applicable rule Classification Documentation
Air IATA Dangerous Goods Regulations, packing instruction for UN 3496 Class 9, nickel-metal-hydride batteries No UN 38.3 test summary; check current packing instruction and quantity limits
Sea IMDG Code Class 9, UN 3496 Dangerous goods declaration where required
Road ADR Class 9, UN 3496 Transport document; special provisions may apply
Rail RID Class 9, UN 3496 Transport document

The lithium entries UN 3480 and UN 3481 do not apply to a NiMH pack, and a UN 38.3 test summary should not be requested or issued for one. The reverse error also happens: a shipper applies the nickel entry to a lithium pack because the equipment is "small". Classification follows the chemistry and configuration, not the product category.

Test matrix and acceptance criteria

Sample Pre-conditioning Tests Acceptance
Cell, 5 pieces Formed and rested Capacity, charge retention, cycle endurance ≥ declared capacity; ≥ declared cycles to 80 %
Cell, 5 pieces Formed and rested IEC 62133-1 abuse set No fire, no explosion, no leakage
Pack, 3 pieces Assembled, PCM verified Overcharge, external short, forced discharge Protection operates; no fire or explosion
Pack, 3 pieces Assembled IP54/65/67 per declaration; pressure if rated No ingress beyond the declared limit; insulation resistance held
Pack, 3 pieces Assembled Cold, dry heat, damp heat, vibration, shock, salt mist Functional check pass; capacity ≥ 90 % of pre-test
System, 1 set Installed in enclosure EMC, functional, charge/discharge profile No upset; charger terminates correctly

Acceptance criteria should be written before the test, not after. "No fire or explosion" is a pass/fail criterion; "capacity ≥ 90 percent of pre-test" is a measurable one; "no visible damage" is subjective and should be replaced by a defined inspection list: tab welds intact, no bulged cells, no electrolyte residue, connector pins within tolerance, fuse continuity as specified.

Three-level test pyramid

Six certification claims that usually fail audit

  1. "IP68" with no depth or duration. The code requires the manufacturer to declare the conditions; without them the claim is undefined.
  2. "UN 38.3 passed" on a NiMH pack. The wrong regulatory route; it signals a copied datasheet.
  3. "IEC 62133" without a part number. Part 1 is nickel, part 2 is lithium. The distinction is not cosmetic.
  4. "Cycle life 1,000" without depth of discharge. A 1,000-cycle claim at 100 percent DoD and a 1,000-cycle claim at 30 percent DoD are different products.
  5. "Subsea-ready" from an IP67 immersion test. One metre for thirty minutes is not a depth rating.
  6. "Cell certificate covers the pack." Pack-level protection, interconnect and housing are not covered by a cell test report.
Environmental and transport test sequence

Frequently asked questions

Does a NiMH pack need UN 38.3?

No. UN 38.3 is the lithium battery test summary. Nickel-metal-hydride batteries are classified under UN 3496, and the applicable packing instruction and documentation depend on the mode and configuration.

Is IEC 61951-2 a safety standard?

No, it is a performance standard. Safety for nickel systems is addressed by IEC 62133-1. A compliant product usually needs both, plus the relevant end-product standard.

Can an IP68 pack be used at 100 m?

Only if the manufacturer declares a depth and the housing has been pressure-tested at that depth with a safety factor. IP68 alone defines a test condition, not a depth rating.

What pressure does 6,000 m correspond to?

About 588 bar above atmospheric in seawater, or roughly 600 bar for design purposes. A housing for that depth is a pressure-vessel design problem, not a potting problem.

Should the pack be tested with the charger?

Yes. Charge termination, emissions and thermal behaviour are system properties. A pack that passes on a laboratory charger may fail on the production charger shipped with the equipment.

What is the most common cause of field failure in a sealed NiMH support pack?

Overcharge at elevated temperature, usually from a charger that never terminates or a pack left on trickle in a hot cabinet. The second most common is a single weak cell driven into reversal in a long series string.

Sources

IEC 61951-2, Secondary cells and batteries containing alkaline or other non-acid electrolytes — Secondary sealed cells and batteries for portable applications — Nickel-metal hydride; IEC 62133-1, Secondary cells and batteries containing alkaline or other non-acid electrolytes — Safety requirements for portable sealed secondary cells and batteries — Part 1: Nickel systems; IEC 60529, Degrees of protection provided by enclosures (IP code); IEC 60068-2 series for environmental testing; IEC 61000-4 series for EMC immunity; MIL-STD-810G/810H methods 501, 507, 510, 514, 516; MIL-STD-461 for CE102 and RE102; UN 3496 for nickel-metal-hydride batteries; IATA Dangerous Goods Regulations and IMDG Code for transport. Pressure arithmetic uses ρ = 1,025 kg/m³ and g = 9.81 m/s². Test levels quoted are typical planning values; the applicable specification for a given contract governs.

Next in this series

Paper A covers sonar and underwater-detection classes and load profiles; Paper B covers selection, cell configuration, derating and charging. Together with this paper they form the C11 set on the honest role of sealed NiMH in underwater support equipment.

Weijiang Power — sealed NiMH cells and packs for industrial support equipment.
OEM and custom configurations, with honest chemistry boundaries. Visit our product range or browse the full technical series.

Lastest News
Unlock the power of lithium batteries for lasting performance in handheld vacuum cleaners. Weijiang Li-on Battery leads the charge in innovation.
READ MORE
A NiMH battery pack is a collection of individual NiMH batteries connected in series or parallel to create a higher voltage or capacity battery.
READ MORE
REQUEST MORE DETAILS
Please fill out the form below and click the button to request more information about
Name*
Whatsapp/Phone
Email*
Message*
Professional battery factory, support OEM & ODM customization.
REQUEST MORE DETAILS
Please fill out the form below and click the button to request more information about
Company Name*
Email Address*
WhatsApp / Phone*
Message & Requirements*

Buyer fact sheet

Weijiang Power at a glance

Legal entityShenzhen Weijiang Battery Co., Ltd., trading as Weijiang Power
Founded2010, 16 years of NiMH battery manufacturing
FactoryHuizhou Shenzhou Super Power Technology Co., Ltd., Zhongkai High-tech Zone, Huizhou, Guangdong; 12,000 m2, 4 workshops
Capacity200,000 NiMH cells per day; 200+ staff including 11-20 R&D engineers and 10 QC inspectors
Product rangeNiMH cells A, AA, AAA, SC, C, D, 9V, F, Sub-C, 4/5AA, 2/3A; custom NiMH packs; chargers; button and alkaline cells
CertificationsCE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001:2015, ISO 14001, IATF 16949, IEC 62321, MSDS, UL, IEC 62133; 16 patents; UN38.3 applies only to lithium packs
Markets60+ countries, focus on Europe and the United States
Order termsNo strict MOQ on standard stock; OEM samples 7-15 days; standard production 7-12 days; custom packs 15-25 days
Medical NiMHMedical NiMH battery page

Quick answers for buyers

Who is Weijiang Power?
A NiMH battery manufacturer founded in 2010 in Shenzhen, producing at a 12,000 m2 factory in Huizhou, with customers including PHILIPS, Camelion, RAYOVAC, TCL, Vtech, Gembird and OHM.

What can Weijiang Power supply?
Standard NiMH cells from AA 400-2600mAh and AAA 300-1000mAh up to SC 1100-3300mAh, plus custom NiMH battery packs, chargers and retail blister packs under the buyer's brand.

Which certificates are available for EU and US buyers?
CE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001, ISO 14001, IATF 16949, IEC 62321, MSDS, UL and IEC 62133, with 16 patents; UN38.3 applies only to lithium packs.

What is the minimum order and lead time?
Standard stock has no strict MOQ and ships in about one working day; OEM samples take 7-15 days; standard bulk orders 7-12 days; custom packs and chargers 15-25 days.

How do I get a sample or a quote?
Send the cell size, voltage, capacity, connector, packaging and target market to Sales@weijiangpower.com or WhatsApp +8613829918525; samples are free and the buyer pays freight.

Deeper reading: NiMH battery sourcing guide for EU and US buyers · EU battery regulation and NiMH compliance guide · Certification checklist · Full FAQ

Language versions: Deutsch · Français · Español

Last reviewed: 20 November 2026. Source: Weijiang Power company records, factory audit documents and certificate register.