Nov.2026 20
Views: 91
Testing and Certifying Sealed NiMH Packs for UAV Ground Support: IEC 61951-2, IEC 62133-1, Ingress, MIL-STD-810/461 and UN 3496
Introduction
Paper C: the qualification chain for sealed NiMH UAV ground-support packs. IEC 61951-2 cell performance, IEC 62133-1 safety tests and sample sizes, IEC 60529 ingress, MIL-STD-810H environmental, MIL-STD-461G EMC, ASTM F3005 boundaries and the mode-specific UN 3496 transport route.
Details

Testing and certifying sealed NiMH packs for UAV ground support — IEC 61951-2, IEC 62133-1, ingress, environmental, EMC and UN 3496

"Military-grade" is a claim, not a test report. A sealed nickel-metal-hydride (NiMH) pack for unmanned-aircraft ground support is qualified by a chain of evidence: cell performance to IEC 61951-2, pack safety to IEC 62133-1, ingress to IEC 60529, environmental robustness to a tailored MIL-STD-810H sequence, electromagnetic compatibility to MIL-STD-461G where the platform requires it, and a transport route that is correctly described for air, sea and road. This paper sets out that chain, the tests that actually matter for a ground-support pack, the sample sizes and sequences that make the results defensible, and the documentation a customer should receive with the first article.

Key facts at a glance

  • Cell performance and pack safety are different standards. IEC 61951-2 describes capacity, cycle life and electrical performance of NiMH cells; IEC 62133-1 describes safety under intended use and foreseeable misuse. A pack needs both, not one or the other.
  • IEC 62133-1 is a type-test standard with defined sample sizes. The 2017 edition specifies five cells or batteries per temperature for external short circuit, three for free fall, five for mechanical shock, five cells for thermal abuse, five cells for crush, three cells for low pressure, five for overcharge and five cells for forced discharge.
  • Ingress is not a single number. IP54, IP65 and IP67 answer different questions: dust protection, water jets and temporary immersion. The enclosure, connectors and vent must be tested as a system.
  • EMC is platform-specific. MIL-STD-461G applies when the customer's platform requires it; a ground cart may need CE102, CS101, CS114, CS115, CS116, RE102 and RS103, while a simple test bench may need only commercial emissions and immunity.
  • UN 3496 is not one regime. By air, NiMH batteries are "Not Restricted" under IATA Special Provision A199 when short-circuit and unintentional activation are prevented. By sea they are UN 3496, Class 9, with special provisions 117 and 963. By road, ADR does not apply. The shipping papers must match the mode.

The qualification chain: cell, pack, platform, logistics

Level What is being proved Governing documents Evidence produced
Cell Capacity, cycle life, charge retention, electrical performance IEC 61951-2; supplier data sheet Cell test report, batch certificate, cycle-life data
Pack Safety under intended use and foreseeable misuse IEC 62133-1 Type-test report with sample traceability
Enclosure Dust and water ingress IEC 60529 IP test report at the declared rating
Platform Vibration, shock, temperature, altitude, humidity, EMC MIL-STD-810H; MIL-STD-461G; customer tailoured profile Environmental and EMC test reports
Logistics Safe transport by air, sea and road IATA DGR Special Provision A199; IMDG UN 3496; ADR Air waybill statement, IMDG declaration where applicable, packing checklist

The chain is cumulative. A pack that passes IEC 62133-1 but fails IP65 at the connector is not an IP65 pack. A pack that passes vibration but loses capacity at −20 °C is not a cold-weather pack. The qualification plan should map each customer requirement to one test and one report line, so that no requirement is left as an assumption.

IEC 61951-2: what the cell has to prove

IEC 61951-2 covers sealed NiMH cells for portable applications. It is a performance standard: it defines how capacity, high- and low-temperature discharge, charge retention and cycle life are measured, and the conditions under which the numbers are comparable. The table below is a practical qualification checklist, not a clause-by-clause reproduction.

Test area What is measured Typical condition Why it matters to a UAV ground pack
Rated capacity Discharge capacity at a defined rate 0.2C to 1.0 V/cell at 20 ± 5 °C Baseline for the sizing calculation
High-temperature discharge Capacity at elevated ambient +45 to +60 °C Flight-line cart in summer; charge temperature limits
Low-temperature discharge Capacity and voltage at cold −18 to −20 °C Winter operations; brown-out risk during pulses
Charge retention Self-discharge over storage 28 days at 20 °C, or customer-defined Pack stored in a vehicle between missions
Cycle life Capacity at defined cycles 0.2C/0.2C to 80 % of rated Two-to-three-year service target
Charge acceptance Ability to accept charge after storage Defined charge profile Opportunity charging from a generator
Overcharge endurance Cell behaviour under continuous low-rate charge 0.1C, 14–16 h Trickle-charged standby packs

The test report should state the cell model, the manufacturer, the date of manufacture, the formation/aging history and the test temperature. A capacity number without those conditions is not comparable to another supplier's number.

IEC 62133-1: what the pack has to survive

IEC 62133-1:2017 (nickel systems) defines safety tests under intended use and reasonably foreseeable misuse. The second edition, IEC 62133-1:2026, keeps the same test families and updates definitions and conditions. The sample sizes in the 2017 edition are shown because they are the ones most test houses still quote.

Clause Test Sample size (cell / battery) Acceptance criterion
7.2.1 Continuous low-rate charging Cells No leakage, no fire, no explosion; defined capacity retention
7.2.2 Vibration Cells / batteries No leakage, no fire, no explosion; voltage and mechanical integrity
7.2.3 Case stress at high ambient temperature Batteries No deformation that compromises safety
7.2.4 Temperature cycling Cells / batteries No leakage, no fire, no explosion
7.3.1 Incorrect installation 5 sets of 4 cells No fire, no explosion
7.3.2 External short circuit 5 per temperature No fire, no explosion
7.3.3 Free fall 3 No fire, no explosion
7.3.4 Mechanical shock 5 No fire, no explosion
7.3.5 Thermal abuse 5 cells No fire, no explosion at 130 °C oven
7.3.6 Crush 5 cells (10 prismatic) No fire, no explosion at 13 kN
7.3.7 Low pressure 3 cells No leakage, no fire, no explosion
7.3.8 Overcharge 5 No fire, no explosion
7.3.9 Forced discharge 5 cells No fire, no explosion under polarity reversal

A pack-level test report should identify which tests were performed on cells and which on finished packs, and should include the pack's protection settings. A common gap is testing cells alone and claiming pack safety; the pack adds connectors, wiring, an enclosure and a thermistor, each of which can change the outcome of a short-circuit or crush test.

Qualification ladder from cell to logistics

Ingress protection: IEC 60529

Rating Dust Water Typical UAV ground-support use Test note
IP54 Protected against dust in harmful quantities Protected against splashing water from any direction Sheltered test bench, vehicle cab Enclosure and connector both assessed
IP55 Dust-protected Protected against water jets Flight-line cart under a canopy Jets from a 6.3 mm nozzle
IP65 Dust-tight Protected against water jets Exposed ground cart, launch trailer Dust-tight requires no ingress of dust
IP67 Dust-tight Protected against temporary immersion Recovery equipment near water, open deck Immersion at defined depth and time

Ingress ratings are not cumulative: IP67 does not automatically mean IP65, and an IP65 connector on an IP54 enclosure gives an IP54 system. The test should be performed on the complete pack, with the connector mated and the vent in place, because that is the configuration the customer will use.

MIL-STD-810H: the environmental sequence

MIL-STD-810H is a method standard, not a pass/fail specification. The customer must define the tailoured test profile: temperature extremes, dwell times, vibration spectrum, shock pulses and altitude. The table below lists the methods most often relevant to a UAV ground-support pack.

Method Title Typical tailoring for a ground-support pack What it reveals
500.6 Low pressure (altitude) Up to 18,000 ft / about 50 kPa, if air-shipped or stored at altitude Enclosure pressure, venting, connector integrity
501.7 High temperature +55 °C ambient, solar load if exposed Charge inhibit, capacity, enclosure deformation
502.7 Low temperature −20 to −30 °C, with operational and storage checks Capacity, voltage sag, charger behaviour
503.7 Temperature shock −20 to +55 °C, rapid transfer Condensation, seals, solder joints
507.6 Humidity 95 % RH, cycling Corrosion, insulation resistance
509.7 Salt fog Coastal or marine exposure Connector and enclosure corrosion
510.7 Sand and dust Blowing dust, if the cart is exposed Ingress, fan and connector fouling
514.8 Vibration Vehicle transport profile, 3 axes Cell movement, tab fatigue, fastener loosening
516.8 Shock Handling drop and transport shock Enclosure cracking, cell displacement

Two sequencing rules make the result more useful. First, run the environmental sequence on the same units that will be opened and inspected, so that internal damage is visible. Second, perform a functional check after each method, not only at the end: a pack that passes the final check may have failed intermittently after vibration and recovered by the time it was measured.

MIL-STD-461G: EMC for the platform

Test Category What it checks Relevance to a NiMH ground pack
CE102 Conducted emissions, power leads Noise fed back onto the power bus Charger and DC-DC ripple; sensitive to layout
CS101 Conducted susceptibility, power leads Immunity to ripple and transients on the bus Generator and winch transients
CS114 Conducted susceptibility, bulk cable injection Immunity to injected RF Cable harness near antennas
CS115 Conducted susceptibility, impulse excitation Immunity to fast transients Relay and contactor switching
CS116 Conducted susceptibility, damped sinusoidal transients Immunity to ringing transients Long cables and ground loops
RE102 Radiated emissions Unintended radio emissions Charger switching harmonics
RS103 Radiated susceptibility Immunity to incident RF fields Operation near datalink and radar

Not every ground cart needs the full MIL-STD-461G set. A pack that sits in a test cell can often be qualified to commercial emissions and immunity standards; a pack that operates beside a tactical radio or a radar should be tested to the platform's tailoured list. The requirement should name the tests, not just the standard.

Flight-pack standards: know the boundary

Document Applies to Does it apply to a NiMH ground pack? Why it still matters
ASTM F3005-22 Batteries for small unmanned aircraft systems (sUAS) Not as a flight approval; useful as a design and documentation checklist Defines cell, mechanical, electrical and maintenance requirements; subordinate to ASTM F2910
RTCA DO-311A Rechargeable lithium battery systems on aircraft No; lithium-specific Shows the level of analysis a flight pack receives
RTCA DO-160G Airborne equipment environmental qualification No, unless the pack is installed in the aircraft Defines the airborne environmental envelope
MIL-PRF-32052 Military battery, 6T format Only if the customer specifies that form factor Connector, case and performance requirements for legacy equipment
IEC 62133-1 Portable sealed nickel cells and batteries Yes, for pack safety Safety baseline for ground and training packs

The boundary is important commercially as well as technically. A supplier that implies a NiMH ground pack is "flight-certified" creates a liability it cannot support. The correct statement is that the pack is qualified for ground support to the named standards and is not a replacement for the aircraft's approved flight battery.

Sample plan and test sequence

Stage Samples Tests Purpose
Cell screening 10–20 cells from the production lot Capacity, internal resistance, self-discharge Confirm lot consistency before pack build
Design verification 3–5 packs IEC 62133-1 safety tests; IP rating Prove the design and protection settings
Environmental 3 packs MIL-STD-810H tailored sequence Prove transport and field robustness
EMC 1–2 packs plus charger MIL-STD-461G tailored list Prove compatibility with the platform
Endurance 5–10 packs Cycle life to 80 % capacity Prove the service-life claim
First article 1 production pack Dimensional, functional, charge/discharge, label Confirm production conformity

The sequence should put non-destructive tests first (capacity, IP, functional), then environmental, then destructive safety tests, and finally endurance on separate samples. Testing a pack to crush and then using it for cycle life is not a valid plan; the sample populations must be independent.

Failure modes and what they reveal

Failure Likely cause Design response Test that catches it
Voltage sag during launch pulse High internal resistance, small cells, long wiring Larger cells, shorter harness, capacitor buffer Pulse discharge at low temperature
Capacity loss after cold soak Electrolyte conductivity, cell mismatch Cell selection, heater or thermal insulation IEC 61951-2 low-temperature discharge
Connector corrosion Salt fog, condensation, dissimilar metals Plated contacts, sealed connector, vent MIL-STD-810H 509.7 and 507.6
Enclosure cracking Drop, shock, brittle resin Ductile material, ribs, crush space IEC 62133-1 free fall; MIL-STD-810H 516.8
Overcharge heating Charger misses termination; no thermistor −ΔV plus dT/dt plus timer plus temperature cut-off IEC 62133-1 overcharge; charge-fault injection
Cell reversal Deep discharge, mismatched cells Low-voltage cutoff at 1.0 V/cell; matched cells IEC 62133-1 forced discharge
Radiated emissions failure Switching charger, poor filtering Input filter, shielding, layout MIL-STD-461G CE102 and RE102

Documentation the customer should receive

Document Content Why it matters
Cell test report Model, lot, capacity, cycle life, temperature performance Traceability and baseline for pack claims
Pack type-test report IEC 62133-1 tests, sample IDs, results, protection settings Evidence of safety qualification
IP test report Rating, test setup, connector configuration, result Defines what "waterproof" means
Environmental report MIL-STD-810H methods, tailoring, functional checks Defines the operating envelope
EMC report MIL-STD-461G tests, limits, setup photos Platform compatibility evidence
Transport statement UN 3496 / A199 wording, state of charge, packing checklist Correct papers for air, sea or road
Instructions and SDS Charge, storage, disposal, safety data sheet Legal and operational requirement

Worked qualification matrix for a 24 V 20 Ah ground cart

Requirement Test Sample Acceptance
Capacity ≥ 20 Ah at 0.2C, 25 °C IEC 61951-2 rated capacity 5 packs ≥ 20 Ah
Usable energy ≥ 250 Wh at −10 °C Low-temperature discharge 3 packs ≥ 250 Wh delivered
No fire or explosion under misuse IEC 62133-1 test set Per clause sample sizes No fire, no explosion
IP54 with mated connector IEC 60529 3 packs No harmful ingress
Transport vibration and drop MIL-STD-810H 514.8 / 516.8 3 packs No loss of function, no cell displacement
Charge/discharge at −20 to +55 °C MIL-STD-810H 501.7 / 502.7 3 packs Functional within derated limits
Conducted and radiated emissions MIL-STD-461G CE102 / RE102 1 pack plus charger Below contractual limits
500 cycles to 80 % capacity Cycle-life test 5 packs ≥ 80 % of rated at 500 cycles

This matrix is deliberately written as requirements with numbers, not as a list of standards. A test plan that says "qualified to MIL-STD-810H" without a temperature, a duration and an acceptance criterion is not auditable, and it will not survive a customer's quality review.

Transport: air, sea and road are different

Mode Classification Key condition Documentation
Air (IATA DGR) Not Restricted under Special Provision A199 Short circuit prevented; unintentional activation prevented Air waybill wording with "Not Restricted" and A199, where an AWB is used
Sea (IMDG) UN 3496, Class 9, special provisions 117 and 963 Packing instruction SP963; terminals protected IMDG declaration where required
Road (ADR) Not applicable Short circuit and activation prevented as good practice No ADR declaration
Storage Not a transport regime 30–50 % state of charge; dry, ventilated, away from heat Internal procedure and SDS

The air case is the one most often mis-documented. UN 3496 is not used as an air waybill description for NiMH; the correct statement is "Not Restricted" with Special Provision A199, provided the batteries are protected against short circuit and unintentional activation. A shipper who writes "UN 3496" on an air waybill has copied a sea or road entry into the wrong regime.

Test sequence and transport routes

Frequently asked questions

Does a NiMH ground-support pack need IEC 62133-1?

It is the most widely accepted safety baseline for portable sealed nickel cells and batteries. A military customer may also require MIL-STD-810H and MIL-STD-461G, but IEC 62133-1 remains the evidence that the pack is safe under intended use and foreseeable misuse.

Is IEC 61951-2 a safety standard?

No. It defines performance tests — capacity, temperature behaviour, charge retention and cycle life. Safety is addressed by IEC 62133-1. A complete qualification uses both.

Can a pack be IP67 without testing the connector?

No. The rating applies to the complete enclosure, including the connector, the vent and the cable entry. A sealed box with an open connector is not IP67, and a test performed with the connector blanked off does not represent the installed configuration.

Does MIL-STD-810H require a fixed test sequence?

No. It provides methods and guidance; the customer must tailor the temperatures, durations, vibration spectrum and shock pulses to the application. The test report should state the tailoring, not just the method number.

What is the difference between UN 3496 and UN 38.3?

UN 38.3 is the lithium-battery transport test regime. Nickel-metal-hydride batteries do not require a UN 38.3 test summary. By sea they are UN 3496, Class 9; by air they are Not Restricted under IATA Special Provision A199 when short-circuit and unintentional activation are prevented.

How long does a full qualification take?

For a mature cell and a defined pack, plan 10–16 weeks: 2–3 weeks for cell screening and pack build, 3–4 weeks for IEC 62133-1, 3–4 weeks for environmental and EMC, and 4–6 weeks for cycle life. Custom tooling, new cells or a first-of-type enclosure can double the schedule.

Sources

IEC 61951-2:2017+AMD1:2022, Secondary cells and batteries containing alkaline or other non-acid electrolytes — Secondary sealed cells and batteries for portable applications — Part 2: Nickel-metal hydride; IEC 62133-1:2017 and IEC 62133-1:2026, Secondary cells and batteries containing alkaline or other non-acid electrolytes — Safety requirements for portable sealed secondary cells, and for batteries made from them, for use in portable applications — Part 1: Nickel systems (test list and sample sizes from the 2017 edition, Table 1); IEC 60529:1989+AMD1:2013+AMD2:2013, Degrees of protection provided by enclosures (IP Code); IATA Dangerous Goods Regulations, Special Provision A199 and the IATA guidance document for UN 3496 nickel-metal-hydride batteries (air transport: Not Restricted; sea: UN 3496 Class 9, special provisions 117 and 963); UNECE ADR and IMDG references for UN 3496; MIL-STD-810H, Methods 500.6, 501.7, 502.7, 503.7, 507.6, 509.7, 510.7, 514.8 and 516.8; MIL-STD-461G, CE102, CS101, CS114, CS115, CS116, RE102 and RS103; ASTM F3005-22 and ASTM F2910; RTCA DO-311A and DO-160G; MIL-PRF-32052. Test durations and sample counts are planning guidance, not a substitute for the customer's qualification plan.

Next in this series

This closes the C13 set on military UAV power. The series continues with the next D7 platform; the three-paper structure — working conditions and principles, selection and design, testing and certification — remains the same.

Weijiang Power — sealed NiMH cells and packs for industrial support equipment.
OEM and custom configurations, with honest chemistry boundaries. Visit our product range or browse the full technical series.

Lastest News
Unlock the power of lithium batteries for lasting performance in handheld vacuum cleaners. Weijiang Li-on Battery leads the charge in innovation.
READ MORE
A NiMH battery pack is a collection of individual NiMH batteries connected in series or parallel to create a higher voltage or capacity battery.
READ MORE
REQUEST MORE DETAILS
Please fill out the form below and click the button to request more information about
Name*
Whatsapp/Phone
Email*
Message*
Professional battery factory, support OEM & ODM customization.
REQUEST MORE DETAILS
Please fill out the form below and click the button to request more information about
Company Name*
Email Address*
WhatsApp / Phone*
Message & Requirements*

Buyer fact sheet

Weijiang Power at a glance

Legal entityShenzhen Weijiang Battery Co., Ltd., trading as Weijiang Power
Founded2010, 16 years of NiMH battery manufacturing
FactoryHuizhou Shenzhou Super Power Technology Co., Ltd., Zhongkai High-tech Zone, Huizhou, Guangdong; 12,000 m2, 4 workshops
Capacity200,000 NiMH cells per day; 200+ staff including 11-20 R&D engineers and 10 QC inspectors
Product rangeNiMH cells A, AA, AAA, SC, C, D, 9V, F, Sub-C, 4/5AA, 2/3A; custom NiMH packs; chargers; button and alkaline cells
CertificationsCE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001:2015, ISO 14001, IATF 16949, IEC 62321, MSDS, UL, IEC 62133; 16 patents; UN38.3 applies only to lithium packs
Markets60+ countries, focus on Europe and the United States
Order termsNo strict MOQ on standard stock; OEM samples 7-15 days; standard production 7-12 days; custom packs 15-25 days
Medical NiMHMedical NiMH battery page

Quick answers for buyers

Who is Weijiang Power?
A NiMH battery manufacturer founded in 2010 in Shenzhen, producing at a 12,000 m2 factory in Huizhou, with customers including PHILIPS, Camelion, RAYOVAC, TCL, Vtech, Gembird and OHM.

What can Weijiang Power supply?
Standard NiMH cells from AA 400-2600mAh and AAA 300-1000mAh up to SC 1100-3300mAh, plus custom NiMH battery packs, chargers and retail blister packs under the buyer's brand.

Which certificates are available for EU and US buyers?
CE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001, ISO 14001, IATF 16949, IEC 62321, MSDS, UL and IEC 62133, with 16 patents; UN38.3 applies only to lithium packs.

What is the minimum order and lead time?
Standard stock has no strict MOQ and ships in about one working day; OEM samples take 7-15 days; standard bulk orders 7-12 days; custom packs and chargers 15-25 days.

How do I get a sample or a quote?
Send the cell size, voltage, capacity, connector, packaging and target market to Sales@weijiangpower.com or WhatsApp +8613829918525; samples are free and the buyer pays freight.

Deeper reading: NiMH battery sourcing guide for EU and US buyers · EU battery regulation and NiMH compliance guide · Certification checklist · Full FAQ

Language versions: Deutsch · Français · Español

Last reviewed: 20 November 2026. Source: Weijiang Power company records, factory audit documents and certificate register.