Nov.2026 20
Views: 53
Testing and Certifying Sealed NiMH Packs for Radar and Communication Station Support Equipment: IEC 61951-2, IEC 62133-1, Ingress and Environmental Sequences, EMC, and the UN 3496 Transport Route
Introduction
Paper C: how to test and certify a sealed NiMH pack for radar and communication station support equipment. Cell performance is qualified to IEC 61951-2, pack abuse safety to IEC 62133-1, and the installed system to IEC 62368-1, ETSI EN 300 132-2, EN 300 253 and EN 300 019, with IP testing to IEC 60529 and EMC to EN 300 386. NiMH ships under UN 3496, not the lithium UN 38.3 route.
Details

Testing and certifying sealed NiMH packs for radar and communication station support equipment

A sealed NiMH pack for a station support device passes three different kinds of test, and they are routinely confused. Cell tests prove the chemistry; pack safety tests prove that the assembly survives abuse; system tests prove that the device it feeds still works on the site. A supplier who only has cell data has not qualified a pack. A supplier who only has a pack safety certificate has not qualified it for the site. This paper sets out the sequence, the standards that actually apply, and the transport route that makes NiMH attractive in the first place.

Key facts at a glance

  • Three levels, three purposes. IEC 61951-2 qualifies the cell's electrical performance; IEC 62133-1 qualifies the pack's safety under abuse; IEC 62368-1 and the ETSI EN 300 series qualify the system and its installation.
  • Environmental testing follows the site, not the product. A non-weather-protected outdoor cabinet is tested to ETSI EN 300 019-1-4 / -2-4 and IEC 61969-3, not to a generic "industrial" profile.
  • Ingress protection is a system property. An IP65 pack inside an IP54 cabinet is an IP54 installation. Test the assembly where the customer will deploy it.
  • NiMH is not lithium on the transport paperwork. It travels under UN 3496, and many configurations qualify for "not restricted" treatment — but the current packing instruction and quantity limits must be checked for every shipment.
  • A certificate is not a test report. Procurement should ask for the report with the sample description, the test laboratory, the date and the actual measured values, not the cover page of a certificate.

The test pyramid

Level What is tested Governing standard What it proves What it does not prove
Cell Capacity, rate capability, charge retention, cycle life IEC 61951-2 The chemistry meets its datasheet That the assembled pack is safe
Pack safety Overcharge, forced discharge, short circuit, vibration, shock, drop, thermal abuse IEC 62133-1 The pack survives defined abuse without fire or explosion That it performs at the site temperature for years
System / installation Electrical safety, input interface, earthing, environment, ingress, EMC IEC 62368-1; ETSI EN 300 132-2; EN 300 253; EN 300 019; IEC 61969-3; IEC 60529; EN 300 386 The installed assembly is safe and reliable on site That a particular shipment conforms
Conformity / production Batch acceptance, routine tests Manufacturer's control plan Every unit shipped matches the qualified design Long-term field behaviour

The pyramid is deliberately narrow at the top. Most procurement failures happen because a buyer accepts cell-level data for a pack-level purchase, or accepts a pack certificate for an installation that adds a charger, a DC-DC converter and an enclosure — three things the certificate never saw.

Level 1 — Cell qualification to IEC 61951-2

IEC 61951-2 is the performance standard for sealed nickel-metal-hydride cells. It defines how capacity, high-rate discharge, charge retention and cycle life are measured, which matters because a capacity number without a test method is a marketing number.

Test Method basis What to record Why it matters at a station
Rated capacity 0.2 It A discharge to the specified end voltage at 20 °C Ah delivered, and the discharge curve Sets the baseline every other figure is compared with
High-rate discharge Discharge at the rated high rate to the end voltage Ah, average voltage, temperature rise Handheld radios and test instruments pulse
Charge retention Store at a defined temperature for a defined period, then discharge at 0.2 It Retained capacity as a percentage Decides whether an autonomy node needs LSD cells
Cycle life Repeated charge/discharge to a defined end-of-life criterion Cycles to 80 % of rated capacity The number the buyer actually cares about
Cell internal resistance AC or DC method at a defined state of charge mΩ, and the spread across the lot Controls voltage sag on pulse loads
Overcharge tolerance Continuous charge at a defined rate and temperature Temperature rise, leakage, capacity change A station charger may trickle for years

Two practical points about cell data. First, capacity is quoted at 0.2 It, which is a slow discharge; a device that draws 2 C will see less. Second, the internal-resistance spread across a lot is as important as the mean — a string is limited by its worst cell, so a supplier who cannot state the spread cannot support a matched-string claim.

Level 2 — Pack safety to IEC 62133-1

IEC 62133-1 is the safety standard for portable sealed secondary cells and batteries using nickel systems. It is an abuse standard: it does not tell you the pack will last ten years, it tells you the pack will not catch fire, vent violently or rupture when something goes wrong.

Category Test Pass criterion (typical) Design implication
Electrical Overcharge at a defined rate and duration No fire, no explosion, no leakage beyond the limit Charger termination must be independent of the pack's own sensor
Electrical Forced discharge through a reversed cell No fire, no explosion String design and LVD; avoid deep series strings without protection
Electrical External short circuit No fire; case temperature limited Fuse or PTC at the pack terminals, correct wire gauge
Mechanical Vibration, shock, free fall, crush No fire, no explosion, no loss of containment Spot-welded tabs, no unsupported wire, robust can
Thermal High-temperature storage, temperature cycling, thermal abuse No fire, no explosion, no leakage Separator and electrolyte choice; cell spacing for heat rejection

The mechanical tests are where low-cost packs fail. A pack built with folded, unsupported nickel tabs and a hot-glued board will pass a capacity test and fail a drop test. If the pack is destined for a vehicle, a mast or an antenna-adjacent shelter, the vibration and shock tests are the ones to ask about first.

Note what IEC 62133-1 does not cover: it is written for portable applications. A pack that is permanently installed in an outdoor cabinet is a different risk profile, and the installation standards below take over.

Level 3 — System and installation

Once the pack is inside a device or a cabinet, the relevant standards change. The table below maps the questions a station buyer actually asks to the standard that answers them.

Question Standard What it covers
Is the device electrically safe? IEC 62368-1 Hazard-based safety for audio/video, information and communication technology equipment
Does it accept the site's DC interface? ETSI EN 300 132-2 Power supply interface at the input to telecom/datacom equipment operating on -48 V DC
Is the earthing and bonding correct? ETSI EN 300 253 Earthing and bonding of ICT equipment powered by -48 V DC
Will it survive the site climate? ETSI EN 300 019-1-4 / -2-4 Environmental classes and test severities for stationary use at non-weather-protected locations
Is the outdoor cabinet adequate? IEC 61969-1 / -3 Design guidelines and environmental requirements/tests for outdoor enclosures
Is the ingress rating real? IEC 60529 IP code classification and test methods
Does it interfere with, or suffer from, other equipment? EN 300 386; EN 55032; EN 55035 EMC for telecom network equipment; emission and immunity for multimedia equipment
Is the UPS performance as specified? IEC 62040-3 UPS performance and test requirements

The ETSI environmental series is the one most often substituted with a generic claim. "Industrial temperature range" is not a test severity. EN 300 019-1-4 defines classes for stationary use at non-weather-protected locations, and EN 300 019-2-4 defines the corresponding test severities — including the extended classes that a shelter on an airfield apron will actually see. A pack qualified to a generic 0–40 °C profile is not qualified for a cabinet that sees −20 °C in winter and +55 °C in summer.

The environmental test sequence

A sensible sequence runs the pack through the environmental stresses in the order that reveals design weaknesses rather than masking them: cold first (mechanical contraction, seal stress), then dry heat (separator and electrolyte), then damp heat (corrosion and insulation), then vibration and shock (tab and weld integrity), then salt mist for coastal sites.

Stress Standard Typical severity for a station pack What fails
Cold IEC 60068-2-1 Storage and operation at the site's lower limit Capacity, seal flexibility, connector brittleness
Dry heat IEC 60068-2-2 Upper shelter temperature, often +55 °C or higher Separator shrinkage, electrolyte loss, LVD drift
Damp heat, cyclic IEC 60068-2-30 Humid shelter or coastal site Corrosion of tabs and PCB, insulation resistance
Vibration IEC 60068-2-6 Sinusoidal sweep across the mounting profile Tab welds, free wires, connector retention
Shock IEC 60068-2-27 Handling and transport drops Case cracking, cell displacement
Salt mist IEC 60068-2-52 Coastal and offshore sites Nickel-plated hardware, connector pins
Ingress IEC 60529 IP54 indoor shelter; IP65/IP67 outdoor node Seal design, gasket compression, cable entry

Test the pack in the enclosure it will ship in, with the connector mated. A bare pack that passes IP65 tells you nothing about the assembly's cable gland.

Illustrative animation: the environmental test sequence — cold, heat, humidity, vibration, salt mist
Illustrative animation — the environmental test sequence. Not a test record.

Ingress protection, read correctly

Code Meaning Where it is appropriate Common misreading
IP54 Dust protected; splashing water Indoor shelter, protected cabinet Assumed to be waterproof
IP65 Dust tight; water jets Outdoor cabinet, exposed node Assumed to survive immersion
IP66 Dust tight; powerful water jets Coastal, high-wind sites Assumed to be the same as IP67
IP67 Dust tight; temporary immersion Flood-prone or washdown locations Assumed to be continuously submersible

The first digit is dust and the second is water; they are independent. A pack can be dust-tight and not water-tight, and a claim of "IP65" on a pack that is installed with an open cable entry is a claim about a component, not an installation.

EMC, for the pack and for the device

A passive NiMH pack is not a significant emitter. The EMC question usually arrives with the charger or the DC-DC converter that sits next to it, and with the device's own switching regulators. The relevant tests are the standard immunity suite — electrostatic discharge, conducted disturbances, surge — plus the emission limits that apply to the equipment class.

Test Standard Why a station device cares
ESD immunity IEC 61000-4-2 Technicians handle packs with charged hands on dry airfield days
Radiated immunity IEC 61000-4-3 Co-siting with transmitters
EFT / burst IEC 61000-4-4 Relay and contactor switching in the shelter
Surge IEC 61000-4-5 Lightning-induced transients on the DC feed
Conducted disturbances IEC 61000-4-6 Long DC cables act as antennas
Emissions EN 55032; EN 300 386 Do not interfere with the site's own receivers

For a military radar installation, the customer may additionally require MIL-STD-461 for EMC and MIL-STD-810 for environmental testing. Those are programme-specific requirements, not defaults, and should be quoted as such.

Transport: the UN 3496 route

Nickel-metal-hydride batteries are classified under UN 3496 in Class 9. This is the point where NiMH is commercially attractive compared with lithium: there is no UN 38.3 test summary requirement of the kind that applies to UN 3480 and UN 3481 lithium batteries, and many NiMH configurations qualify for "not restricted" treatment for air transport.

Item NiMH Lithium-ion Lead-acid
UN number UN 3496 UN 3480 (cells) / UN 3481 (with equipment) UN 2794
Class 9 9 8
UN 38.3 test summary Not applicable Required Not applicable
Air transport Often "not restricted" depending on configuration and quantity Restricted; state of charge and packing rules apply Restricted; corrosive
Documentation Classification statement and packing instruction as applicable Test summary, DG declaration, trained shipper DG declaration, trained shipper

Two warnings. First, "not restricted" is a property of a specific configuration — cell or battery, packed with equipment or alone, quantity per package — not of the chemistry in general. The current edition of the IATA Dangerous Goods Regulations and the applicable special provisions must be checked for each shipment. Second, a supplier's statement that "NiMH is not dangerous goods" is an over-simplification and should not be accepted in writing.

A test matrix a buyer can actually use

Stage Sample Tests Deliverable
Design verification, cell Cells from the production lot Capacity, high rate, charge retention, cycle life, IR Cell test report with curves
Design verification, pack Prototype packs, 5–10 IEC 62133-1 electrical, mechanical and thermal abuse Pack safety report
Design verification, system Pack in its enclosure with charger IEC 62368-1, IP, EMC, environmental sequence System test report
Production acceptance 100 % of units Open-circuit voltage, IR, visual, leak check Batch record
Batch audit Sample per lot Capacity at 0.2 C, 30-day self-discharge Lot certificate with measured values
Field validation Pilot units at the site Temperature log, capacity check at 6 and 12 months Field report

Acceptance criteria that are worth writing down

Criterion Suggested value Test condition
Capacity ≥95 % of rated at 0.2 It 20 °C, fresh pack
Capacity after 30 days storage ≥90 % (LSD) / ≥75 % (standard) 20 °C, open circuit
Internal resistance Within the supplier's declared band; no cell more than 20 % above the lot mean 50 % state of charge
Leakage None visible; no electrolyte on the case or connector After thermal and vibration tests
Insulation resistance ≥10 MΩ at the declared test voltage After damp heat
Mechanical integrity No cracked case, no loose tab, no displaced cell After drop and vibration
Protection function LVD opens at the specified voltage; fuse opens on the specified fault current Functional test on sample units

Illustrative animation: the test pyramid from cell to pack to installed system
Illustrative animation — the three-level test pyramid and the documents each level produces. Not a certification record.

Where certification claims go wrong

  • Certificate without a scope. A certificate that names a cell family but not the pack assembly does not cover the pack. Check the scope statement.
  • Report without a sample description. If the report does not describe the cell, the string configuration and the enclosure, it cannot be mapped onto your product.
  • Standard version mismatch. IEC 61951-2 and IEC 62133-1 have amendments; a report to a superseded edition may not satisfy the current buyer.
  • Laboratory accreditation gap. Ask whether the laboratory is accredited for the specific test method, not just for the standard family.
  • "Equivalent to" claims. A report to a national standard that mirrors an IEC standard is usually acceptable, but the mapping should be stated, not implied.

Frequently asked questions

Does a NiMH pack need UN 38.3?

No. UN 38.3 is the lithium battery test sequence. NiMH falls under UN 3496, and the transport requirements are different. That does not mean NiMH is unregulated — the classification and packing rules still apply.

Is IEC 62133-1 enough for an installed pack?

No. It is a portable-product safety standard. An installed pack in an outdoor cabinet also needs the installation standards: IEC 62368-1 for the equipment, ETSI EN 300 019 for the environment, IEC 61969-3 for the enclosure and IEC 60529 for ingress.

How long does a full qualification take?

Cell cycle-life testing alone can run for months, so a programme should start with the cell data the supplier already has and run pack and system tests in parallel. A realistic plan is weeks for pack safety and system tests, and months for a full cycle-life claim at the target depth of discharge.

Can I accept a supplier's self-declaration?

For a low-risk accessory, sometimes. For a pack that will sit in an unattended shelter for years, ask for the report. A self-declaration tells you what the supplier believes; a report tells you what was measured.

What is the most common test failure?

In our experience across this product category, it is mechanical rather than electrical: tab welds and connector retention after vibration and drop. The second most common is capacity shortfall after thermal cycling, which usually traces back to electrolyte loss or separator deformation rather than to the cell's initial capacity.

Does the pack need to be tested at the site temperature?

The environmental sequence should bracket the site temperature, and the capacity acceptance test should be repeated at the cold limit if the device is required to work there. A 20 °C capacity test alone does not prove cold performance.

Is a NiMH pack "RoHS compliant"?

RoHS restricts substances in electrical and electronic equipment; batteries have their own regime under the EU Batteries Regulation. A supplier should be able to state the substance status of the cell and the pack separately, and should not conflate the two declarations.

Sources and further reading

  • IEC 61951-2, Secondary cells and batteries containing alkaline or other non-acid electrolytes — Secondary sealed cells and batteries for portable applications — Part 2: Nickel-metal hydride.
  • IEC 62133-1, Safety requirements for portable sealed secondary cells and batteries — Part 1: Nickel systems.
  • IEC 62368-1, Audio/video, information and communication technology equipment — Part 1: Safety requirements.
  • ETSI EN 300 132-2, Power supply interface at the input to telecommunications and datacom equipment — Part 2: Operated by -48 V direct current.
  • ETSI EN 300 253, Earthing and bonding of ICT equipment powered by -48 V DC in telecom and data centres.
  • ETSI EN 300 019-1-4 and EN 300 019-2-4, Environmental conditions and tests for telecommunications equipment — stationary use at non-weather-protected locations.
  • IEC 61969-1 and IEC 61969-3, Mechanical structures for electrical and electronic equipment — Outdoor enclosures.
  • IEC 60529, Degrees of protection provided by enclosures (IP code).
  • IEC 60068-2-1, -2, -6, -27, -30 and -52, Environmental testing.
  • IEC 62040-3, Uninterruptible power systems — method of specifying performance and test requirements.
  • EN 300 386, EMC for telecommunications network equipment; EN 55032 and EN 55035.
  • UN Manual of Tests and Criteria, UN 3496; IATA Dangerous Goods Regulations, current edition.

This paper describes a test strategy, not a certification. The applicable edition of each standard, the acceptance criteria and the scope of any certificate must be confirmed with the test laboratory and the customer before a qualification programme is opened.

Next in this series

The C10 sequence closes here. Paper A set out the operating conditions of radar and communication stations; Paper B turned them into a sizing method for sealed NiMH support packs; Paper C has set out how to prove the result. The next product block moves to C11, sonar and underwater detection support power.

If you need a qualification plan for a station support pack — cell data review, pack safety route, environmental sequence and transport classification — send us the device, the site profile and the target market. We will return a test matrix and a documentation list. Weijiang Power — sealed NiMH cells and packs for industrial support equipment.

Lastest News
Unlock the power of lithium batteries for lasting performance in handheld vacuum cleaners. Weijiang Li-on Battery leads the charge in innovation.
READ MORE
A NiMH battery pack is a collection of individual NiMH batteries connected in series or parallel to create a higher voltage or capacity battery.
READ MORE
REQUEST MORE DETAILS
Please fill out the form below and click the button to request more information about
Name*
Whatsapp/Phone
Email*
Message*
Professional battery factory, support OEM & ODM customization.
REQUEST MORE DETAILS
Please fill out the form below and click the button to request more information about
Company Name*
Email Address*
WhatsApp / Phone*
Message & Requirements*

Buyer fact sheet

Weijiang Power at a glance

Legal entityShenzhen Weijiang Battery Co., Ltd., trading as Weijiang Power
Founded2010, 16 years of NiMH battery manufacturing
FactoryHuizhou Shenzhou Super Power Technology Co., Ltd., Zhongkai High-tech Zone, Huizhou, Guangdong; 12,000 m2, 4 workshops
Capacity200,000 NiMH cells per day; 200+ staff including 11-20 R&D engineers and 10 QC inspectors
Product rangeNiMH cells A, AA, AAA, SC, C, D, 9V, F, Sub-C, 4/5AA, 2/3A; custom NiMH packs; chargers; button and alkaline cells
CertificationsCE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001:2015, ISO 14001, IATF 16949, IEC 62321, MSDS, UL, IEC 62133; 16 patents; UN38.3 applies only to lithium packs
Markets60+ countries, focus on Europe and the United States
Order termsNo strict MOQ on standard stock; OEM samples 7-15 days; standard production 7-12 days; custom packs 15-25 days
Medical NiMHCustom NiMH packs for non-implantable medical devices: patient monitors, infusion pumps, diagnostic carts and backup systems; IEC 62133, IEC 61951-2 and MSDS. Medical NiMH page

Quick answers for buyers

Who is Weijiang Power?
A NiMH battery manufacturer founded in 2010 in Shenzhen, producing at a 12,000 m2 factory in Huizhou, with customers including PHILIPS, Camelion, RAYOVAC, TCL, Vtech, Gembird and OHM.

What can Weijiang Power supply?
Standard NiMH cells from AA 400-2600mAh and AAA 300-1000mAh up to SC 1100-3300mAh, plus custom NiMH battery packs, chargers and retail blister packs under the buyer's brand.

Which certificates are available for EU and US buyers?
CE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001, ISO 14001, IATF 16949, IEC 62321, MSDS, UL and IEC 62133, with 16 patents; UN38.3 applies only to lithium packs.

What is the minimum order and lead time?
Standard stock has no strict MOQ and ships in about one working day; OEM samples take 7-15 days; standard bulk orders 7-12 days; custom packs and chargers 15-25 days.

How do I get a sample or a quote?
Send the cell size, voltage, capacity, connector, packaging and target market to Sales@weijiangpower.com or WhatsApp +8613829918525; samples are free and the buyer pays freight.

Deeper reading: NiMH battery sourcing guide for EU and US buyers · EU battery regulation and NiMH compliance guide · Certification checklist · Full FAQ

Language versions: Deutsch · Français · Español

Last reviewed: 20 November 2026. Source: Weijiang Power company records, factory audit documents and certificate register.