Nov.2026 20
Views: 71
Selecting and Sizing Sealed NiMH Packs for Radar and Communication Station Support Equipment: Load Audit, Cell Configuration, Hold-Up Versus Autonomy, Derating and Charging
Introduction
Paper B: how to select and size a sealed NiMH pack for station support equipment. Start from the duty class — hold-up, one-shift portable power or multi-day autonomy — then audit the load including standby, configure the 1.2 V string, and apply the temperature, rate, end-of-life and wiring derating stack. NiMH is not a drop-in for a float-charged -48 V plant; it needs current-limited charging with negative-delta-V or temperature-rise termination, pack-level LVD, fusing and a thermal sensor.
Details

Selecting and sizing sealed NiMH packs for radar and communication station support equipment

Most sealed NiMH packs used around radar and radio sites are not designed — they are copied. A previous product's 4 Ah pack becomes the next product's 4 Ah pack, the cell count is whatever the old charger expects, and the capacity is whatever fits the enclosure. The pack then works in the lab, degrades in a hot shelter, and fails in the third winter. This paper sets out a sizing method that starts from the duty the pack actually has to perform, applies the derating stack in the right order, and ends with a charging and protection design that matches the chemistry rather than fighting it.

Key facts at a glance

  • Start from the duty, not the catalogue. Hold-up, shift-length portable power and multi-day autonomy are three different design problems, and they produce packs that differ by an order of magnitude in capacity.
  • NiMH is a 1.2 V cell. Strings are built in multiples of 1.2 V — 6S for 7.2 V, 12S for 14.4 V, 20S for 24 V, 40S for 48 V — and the end-of-discharge voltage is around 1.0 V per cell under load, not 1.2 V.
  • Derating is multiplicative and must be applied to energy, not to current. Cold, high rate, end of life and wiring losses typically remove 30–40 percent of the nameplate capacity before anything goes wrong.
  • NiMH cannot be treated as a drop-in for a float-charged lead-acid string. It needs current-limited charging with a proper termination criterion, and it dislikes continuous high-voltage trickle.
  • Protection belongs at the pack, not only at the charger. A pack that relies on the charger to prevent over-discharge will eventually be discharged by a user who plugs it into the wrong device.

Why station support packs fail in service

Field returns from this segment cluster around five causes, and only one of them is a cell-quality problem.

Failure mode What actually happened Design fix
Capacity shortfall in winter Pack sized at 25 °C; site ambient −10 °C; NiMH delivers materially less usable capacity when cold Cold derating in the calculation; insulation or heater where justified
Early death in a hot shelter Continuous trickle at elevated temperature; electrolyte dry-out and separator degradation Lower trickle or intermittent top-up; thermal placement away from heat sources
One cell fails, whole string dies No cell matching, no per-cell monitoring; a weak cell reverses on deep discharge Matched cells from one lot; pack-level LVD; periodic capacity test
Charger never terminates Charger designed for NiCd (−ΔV too small to detect on NiMH); pack overheats Temperature-rise or timer termination; charger marked for NiMH
Connector or wiring loss Voltage drop at high pulse current; connector heating Size on peak current, not average; crimp and test

None of these are solved by buying a more expensive cell. They are solved by writing the duty down before the pack is specified.

Step 1 — Classify the duty into one of three types

Every station support pack does one of three jobs. Decide which, because the sizing maths and the chemistry trade-offs are different for each.

Duty class Typical station example Energy needed Dominant constraint
Hold-up Keep a handheld terminal alive across a mains transfer; bridge a reboot Watt-hours, small Power delivery and voltage sag, not capacity
Portable shift power Test instrument or handheld radio for one shift Tens of watt-hours Energy density and swap logistics
Autonomy Remote auxiliary node running for a day or more between charges Hundreds of watt-hours Self-discharge, cold, and enclosure volume

A hold-up pack is sized by current and internal resistance. A shift pack is sized by energy. An autonomy pack is sized by energy plus self-discharge plus the solar or mains recharge window. Mixing the three is how a 4 Ah pack ends up proposed for a 24-hour node.

Step 2 — Audit the load, including the parts nobody lists

A load audit for a station pack should capture four categories: continuous, intermittent, pulse, and parasitic. The last one is the one that ruins autonomy calculations — a monitoring board, a status LED and a leaking input capacitor can easily add 10 to 30 percent to a small load.

Load category Example How to measure How to use it
Continuous Receiver, sensor, monitoring board DMM or logging power meter over 10 min Average current × hours
Intermittent Transmit bursts, display backlight, motor Duty-cycle the measurement Energy per event × events per shift
Pulse Radio transmit, camera flash, solenoid Current probe with capture Peak current for connector and protection; energy for capacity
Parasitic / standby Sleep current, LED, leakage µA meter in sleep mode Multiply by the full standby period — often the largest term

Two practical rules. First, measure at the pack terminals, not at the device input, so that converter losses are included. Second, measure at the temperature the pack will actually see; a load that draws 200 mA at 25 °C may draw more at −20 °C if it contains a switching converter with a fixed output power.

Step 3 — Choose the chemistry on the merits, then defend the choice

Sealed NiMH is one option among several, and the honest comparison table looks like this.

Attribute Sealed NiMH VRLA lead-acid LiFePO4 Li-ion (NMC/LCO) Primary lithium
Nominal cell voltage 1.2 V 2.0 V 3.2 V 3.6/3.7 V 3.0–3.6 V
Energy density (order) Moderate Low High High Very high
Pulse capability Good Moderate Good Good Limited
Cold performance Reduced below 0 °C Reduced Reduced but better Reduced Reduced
Float / trickle tolerance Poor to moderate Good Moderate (needs BMS) Poor (needs BMS) Not applicable
Transport UN 3496, not restricted by air in many cases UN 2794, class 8 UN 3480/3481, class 9 UN 3480/3481, class 9 Class 9 in many formats
End-of-life Nickel recycling; no cadmium, no lead Lead recycling, regulated Lithium recycling, evolving Lithium recycling, evolving Mixed
Best station role Instruments, handhelds, small nodes, training Main DC plant, UPS Main DC plant, high-cycle Compact high-energy devices Long-standby, single-use

The table explains why NiMH keeps a role even where lithium is cheaper per watt-hour: it is a mature, abuse-tolerant, low-voltage chemistry with no mandatory battery management electronics, no pressurised cell, and a transport classification that does not require a UN 38.3 test summary for every shipment. For a maintenance instrument that is charged nightly and dropped occasionally, those properties are worth more than the last 20 percent of energy density.

Step 4 — Configure the string

NiMH strings are built from 1.2 V cells, and the voltage that matters is the end-of-discharge voltage, not the nominal. A cell that is nominally 1.2 V is around 1.0 V at the end of a practical discharge under load, and can be lower at high rate or low temperature. Equipment that needs a minimum 10.8 V, for example, cannot be fed from a 9-cell string that ends at 9.0 V.

String Nominal Approx. end-of-discharge (1.0 V/cell) Typical station use
3S 3.6 V 3.0 V Small sensor, LED task light
6S 7.2 V 6.0 V Handheld radio, legacy instrument
10S 12.0 V 10.0 V 12 V test equipment
12S 14.4 V 12.0 V 14.4 V instrument pack
20S 24 V 20 V 24 V auxiliary node
40S 48 V 40 V 48 V buffer, DC-DC-fed node

Two configuration rules that are routinely broken:

  • Never mix cell lots. A string is limited by its weakest cell, and a mismatched cell will reverse on deep discharge long before the good cells are empty. Buy matched cells from one production lot and keep the lot traceable.
  • Do not exceed the charger's cell count. A 20S pack on a charger designed for 12S will either refuse to start or overcharge the string. If the charger is fixed, the string is fixed.

The 40S case deserves a note because it looks like a telecom drop-in. Forty NiMH cells at the -48 V plant's -53.5 V float works out to about 1.34 V per cell, which is inside the range some NiMH designs will tolerate continuously. But tolerance is not the same as suitability: NiMH does not like sustained overcharge at elevated temperature, and a pack sitting on a live bus for years will lose electrolyte and capacity. If a NiMH pack must coexist with a -48 V bus, feed it through a dedicated charger or a DC-DC stage with its own charge control; do not hang it directly on the plant and call it a battery.

Step 5 — Calculate capacity with the derating stack

The calculation is a chain, and the order matters:

Crequired (Ah) = Eload (Wh) ÷ Vaverage ÷ (ηtemp × ηrate × ηEOL × ηwiring)

where Vaverage is the average discharge voltage (roughly 1.15–1.2 V per cell for a slow discharge, lower at high rate), and the efficiency factors are all less than one.

Factor Typical value When to use it
Temperature, ηtemp 0.85 at 0 °C; 0.70–0.75 at −20 °C; 1.0 at 20–25 °C Always if the site goes below 10 °C
Rate, ηrate 0.85–0.95 Discharge faster than about C/2
End of life, ηEOL 0.80–0.85 Always — a pack is replaced at 80 % capacity, not at 0 %
Wiring and connector, ηwiring 0.95–0.98 Always; lower for long leads or high pulse current
Self-discharge over standby 1–3 %/month (LSD); 20–30 %/month (standard) Autonomy packs that sit for weeks

Worked example 1 — portable test terminal, illustrative. A 14.4 V (12S) instrument draws 8 W average over a 6-hour shift, so 48 Wh. With ηtemp 0.85 at a cold site, ηrate 0.95, ηEOL 0.85 and ηwiring 0.97, the denominator is about 0.665, so the pack must store about 72 Wh. At an average discharge voltage of 13.8 V that is 5.2 Ah, so the nearest standard size is 5.5 or 6 Ah rather than the 4 Ah the previous product used.

Worked example 2 — auxiliary sensor node, illustrative. A 24 V (20S) node draws 3 W continuously and must run 24 hours between visits: 72 Wh. With the same stack the requirement is about 108 Wh, or 4.5 Ah at 24 V. Adding a 2 W heater for winter would double it; adding a parasitic 20 mA standby load at 24 V adds 11.5 Wh per day, which is 16 percent — enough to erase the margin if it is left out.

Worked example 3 — hold-up, illustrative. A 12 V terminal drawing 20 W must ride through a 10-minute transfer: 3.3 Wh. After derating, about 5 Wh, or 0.4 Ah at 12 V. The pack is tiny; the real design question is whether its internal resistance can deliver the 20 W without dropping below the terminal's brown-out threshold. That is a current question, not a capacity question.

Example Load Raw energy Derated energy Resulting capacity
Test terminal, 6 h shift 8 W average 48 Wh ≈72 Wh ≈5.2 Ah at 13.8 V (choose 5.5–6 Ah)
Sensor node, 24 h autonomy 3 W continuous 72 Wh ≈108 Wh ≈4.5 Ah at 24 V
Terminal hold-up, 10 min 20 W 3.3 Wh ≈5 Wh ≈0.4 Ah at 12 V; check IR

Illustrative animation: the derating stack from nameplate capacity to usable capacity
Illustrative animation — how temperature, rate, end-of-life and wiring factors reduce usable capacity. Not measured data.

Step 6 — Design the charge path

NiMH charging is a current-limited process with a termination event. The three accepted termination methods are voltage drop (−ΔV), temperature rise (dT/dt), and a timeout; a good charger uses at least two of them.

Parameter Typical value Notes
Fast charge rate 0.5–1 C Only with temperature sensing and −ΔV detection
−ΔV termination 5–10 mV per cell Small on NiMH; easy to miss at low charge rates
dT/dt termination ≈1 °C per minute The most reliable signal in a hot enclosure
Timer backup ≈1.2 × expected charge time Prevents indefinite overcharge if detection fails
Trickle after full charge 0.03–0.05 C, or intermittent top-up Lower is better in a hot shelter
Charge temperature window 0–40 °C, with reduced rate at the ends Do not fast-charge a frozen pack
Cell end voltage ≈1.4–1.45 V per cell at full charge Open-circuit, after rest

A charger designed for NiCd will usually fail on NiMH: the voltage drop at full charge is smaller, and a NiCd charger's fixed timer will overcharge a NiMH pack that self-heats. If a station's existing charger cannot be reconfigured, the pack should be built to the charger's profile rather than the other way round.

Step 7 — Put protection in the pack

The minimum protection set for a station support pack is:

  • A resettable or one-shot fuse on the pack output, rated above the highest legitimate pulse and below the connector's rating.
  • A low-voltage cutoff that opens the string before any cell can reverse — typically around 1.0 V per cell under load, with a margin for cold and high rate.
  • A temperature sensor bonded to the centre of the pack, wired to the charger, and ideally also to the device so that it can refuse to charge or discharge when hot.
  • An optional PTC in each parallel group, if the pack is built from parallel cells, to limit fault current.
  • Connector keying so that a 14.4 V pack cannot be plugged into a 24 V device.

Pack-level protection is not a substitute for a correctly designed charger, and a charger is not a substitute for pack-level protection. They cover different faults: the charger covers overcharge, the pack covers over-discharge, short circuit and external abuse.

Step 8 — Mechanical and thermal details that decide field life

Detail Recommendation Why
Cell spacing Leave a gap between cells; avoid a solid potted block NiMH generates heat at the end of charge; a potted block traps it
Thermal sensor placement Centre of the pack, bonded to a cell can Edge placement reads the enclosure, not the cells
Enclosure IP54 minimum for shelter use; IP65+ for outdoor nodes Dust and humidity dominate field failures
Vibration Spot-welded tabs, no free wire, conformal coat the board Vehicle-mounted and antenna-adjacent packs see continuous vibration
Serviceability Replaceable pack, labelled with chemistry, voltage and date code Prevents a lithium charger being used on a NiMH pack

Illustrative animation: charge profile with negative delta-V and temperature-rise termination
Illustrative animation — NiMH charge termination by voltage drop and temperature rise. Not a measured curve.

Procurement checklist

  1. Duty class stated (hold-up, shift, autonomy) and the load audit attached.
  2. Voltage window at the device input, including brown-out threshold, and the end-of-discharge voltage of the proposed string.
  3. Temperature range at the pack, and the derating factor used.
  4. Required cycle life at the actual depth of discharge, not at 100 percent.
  5. Charger profile: rate, termination method, trickle, cell count.
  6. Protection set: fuse, LVD, temperature sensor, connector keying.
  7. Transport classification and the documentation that goes with it.
  8. Acceptance test: capacity at 0.2 C, internal resistance, self-discharge over 30 days, and a visual/leakage check.

Frequently asked questions

Can I use a 40-cell NiMH string as a -48 V telecom battery?

Mechanically it fits the voltage window, but it is not a plant battery. NiMH tolerates continuous float less well than VRLA, has different charge termination needs, and is not available in the ampere-hour sizes a plant is designed around. Use it behind a dedicated charger or DC-DC stage, not directly on the bus.

How much capacity does cold really take?

Plan on roughly 85 percent at 0 °C and 70 to 75 percent at −20 °C for a moderate discharge rate. High-rate discharges lose more. The exact figure depends on the cell, so ask for the discharge curve at the target temperature rather than a single number.

Is low self-discharge (LSD) NiMH worth the cost?

For autonomy packs that sit for weeks between charges, yes — the difference between 1–3 percent per month and 20–30 percent per month is the difference between a 24-hour node and a 3-day node. For a pack charged every night, standard cells are usually fine.

How many cells in parallel?

As few as possible. Parallel strings hide a weak cell and complicate protection. If capacity demands it, use parallel cells within a group with individual fusing, and keep the group small.

Does a NiMH pack need a BMS?

Not in the lithium sense — there is no cell-level semiconductor switching in a typical NiMH pack. It does need a charger with the right termination, a pack-level LVD, a fuse and a temperature sensor. That set is simpler and cheaper than a lithium BMS, which is part of NiMH's appeal for low-cost station devices.

What is the realistic cycle life?

Several hundred to about a thousand cycles to 80 percent capacity for good cells at moderate depth of discharge and 20–25 °C, less at high temperature or full depth. Specify the number at your actual duty; a catalogue figure at 100 percent depth and 20 °C is not a field prediction.

Can the pack be shipped by air?

Nickel-metal-hydride batteries are classified under UN 3496 and are not restricted for air transport in many configurations. The exact requirement depends on packaging and quantity; Paper C covers the transport route in detail.

Sources and further reading

  • IEC 61951-2, Secondary cells and batteries containing alkaline or other non-acid electrolytes — Secondary sealed cells and batteries for portable applications — Part 2: Nickel-metal hydride.
  • IEC 62133-1, Secondary cells and batteries containing alkaline or other non-acid electrolytes — Safety requirements for portable sealed secondary cells, and for batteries made from them, for use in portable applications — Part 1: Nickel systems.
  • UN Manual of Tests and Criteria, UN 3496 entry for nickel-metal hydride batteries.
  • ETSI EN 300 132 series, power supply interface at the input to telecommunications and datacom equipment; ETSI EN 300 253, earthing and bonding for -48 V DC equipment.
  • Published radar and telecom site specifications cited in Paper A of this series.

All worked examples in this paper are illustrative and use assumed loads and derating factors. They show the method, not a recommended product configuration. A real design must use measured loads at the actual site temperature.

Next in this series

Paper C sets out how to prove the design: the cell and pack test standards, the environmental sequence for a non-weather-protected site, ingress and EMC testing, and the transport classification that lets a NiMH pack move by air without a lithium-style test summary.

Send us the duty class, the load audit and the temperature range, and we will return a cell configuration, a derating calculation and a charger specification. Weijiang Power — sealed NiMH cells and packs for industrial support equipment.

Lastest News
Unlock the power of lithium batteries for lasting performance in handheld vacuum cleaners. Weijiang Li-on Battery leads the charge in innovation.
READ MORE
A NiMH battery pack is a collection of individual NiMH batteries connected in series or parallel to create a higher voltage or capacity battery.
READ MORE
REQUEST MORE DETAILS
Please fill out the form below and click the button to request more information about
Name*
Whatsapp/Phone
Email*
Message*
Professional battery factory, support OEM & ODM customization.
REQUEST MORE DETAILS
Please fill out the form below and click the button to request more information about
Company Name*
Email Address*
WhatsApp / Phone*
Message & Requirements*

Buyer fact sheet

Weijiang Power at a glance

Legal entityShenzhen Weijiang Battery Co., Ltd., trading as Weijiang Power
Founded2010, 16 years of NiMH battery manufacturing
FactoryHuizhou Shenzhou Super Power Technology Co., Ltd., Zhongkai High-tech Zone, Huizhou, Guangdong; 12,000 m2, 4 workshops
Capacity200,000 NiMH cells per day; 200+ staff including 11-20 R&D engineers and 10 QC inspectors
Product rangeNiMH cells A, AA, AAA, SC, C, D, 9V, F, Sub-C, 4/5AA, 2/3A; custom NiMH packs; chargers; button and alkaline cells
CertificationsCE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001:2015, ISO 14001, IATF 16949, IEC 62321, MSDS, UL, IEC 62133; 16 patents; UN38.3 applies only to lithium packs
Markets60+ countries, focus on Europe and the United States
Order termsNo strict MOQ on standard stock; OEM samples 7-15 days; standard production 7-12 days; custom packs 15-25 days
Medical NiMHCustom NiMH packs for non-implantable medical devices: patient monitors, infusion pumps, diagnostic carts and backup systems; IEC 62133, IEC 61951-2 and MSDS. Medical NiMH page

Quick answers for buyers

Who is Weijiang Power?
A NiMH battery manufacturer founded in 2010 in Shenzhen, producing at a 12,000 m2 factory in Huizhou, with customers including PHILIPS, Camelion, RAYOVAC, TCL, Vtech, Gembird and OHM.

What can Weijiang Power supply?
Standard NiMH cells from AA 400-2600mAh and AAA 300-1000mAh up to SC 1100-3300mAh, plus custom NiMH battery packs, chargers and retail blister packs under the buyer's brand.

Which certificates are available for EU and US buyers?
CE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001, ISO 14001, IATF 16949, IEC 62321, MSDS, UL and IEC 62133, with 16 patents; UN38.3 applies only to lithium packs.

What is the minimum order and lead time?
Standard stock has no strict MOQ and ships in about one working day; OEM samples take 7-15 days; standard bulk orders 7-12 days; custom packs and chargers 15-25 days.

How do I get a sample or a quote?
Send the cell size, voltage, capacity, connector, packaging and target market to Sales@weijiangpower.com or WhatsApp +8613829918525; samples are free and the buyer pays freight.

Deeper reading: NiMH battery sourcing guide for EU and US buyers · EU battery regulation and NiMH compliance guide · Certification checklist · Full FAQ

Language versions: Deutsch · Français · Español

Last reviewed: 20 November 2026. Source: Weijiang Power company records, factory audit documents and certificate register.