Nov.2026 21
Views: 102
Selecting and Sizing Sealed NiMH Packs for Counter-UAS Support Equipment: Load Audit, Cell Configuration, Derating, Charging and Protection
Introduction
Paper B: a sizing procedure for sealed NiMH packs used around counter-UAS systems. Load audit, chemistry comparison, 12/24/48 V architectures, capacity and pulse arithmetic, derating stack, charge termination, protection and procurement questions.
Details

Selecting and sizing sealed NiMH packs for counter-UAS support equipment

Sizing a sealed NiMH pack for counter-UAS support equipment starts with a load audit, not with a catalogue page. The pack must carry a defined mix of C2, sensor, datalink, test and charging loads for a defined time, at a defined temperature, with a defined end-of-life margin, and it must survive the largest pulse the system can produce. This paper gives a six-step procedure that turns those inputs into a cell count, a capacity, a connector and a protection scheme. Every worked example is marked illustrative; the method, not the number, is the deliverable.

Key facts at a glance

  • Start from the energy budget, not the voltage. A 24 V 40 Ah pack is 960 Wh nominal; whether that is enough depends on the average load, the duty cycle and the derating stack, not on the voltage label.
  • Size for the worst-case load, then check the average. A jammer pulse, radar burst or motor start can collapse a pack whose continuous rating is adequate. The pulse rating and the voltage sag are separate specifications.
  • Derating is multiplicative. Temperature, depth of discharge, end of life, discharge rate and wiring losses multiply; a 0.80 × 0.90 × 0.85 × 0.95 × 0.97 stack leaves about 0.60 of nameplate capacity.
  • NiMH has a flat 1.2 V cell and a forgiving charge profile. That makes it a good fit for ground carts, test benches and training sets; it does not make it a good fit for a 300 Wh man-portable tactical pack.
  • Protection is part of the pack, not an accessory. Fuse, breaker, low-voltage disconnect, reverse-polarity protection, thermistor and an enclosure rated for the environment belong in the specification.

Step 1 — Load audit

List every load the pack will supply, its active power, its standby power and its duty cycle. Do not use the system's total nameplate; use the measured or specified load of each box. The table below is a template for a vehicle-mounted counter-UAS support cart.

Load Active power Standby power Duty cycle Energy per 4 h Notes
C2 laptop and display 90 W 8 W 100 % 360 Wh Display brightness dependent
Datalink radio 40 W transmit 10 W receive 10 % transmit ≈ 50 Wh Receive power counted separately
EO/IR gimbal 25 W 5 W 100 % 100 Wh Heater intermittent
Radar processor 60 W 10 W 100 % 240 Wh Pulse peak supplied by capacitor bank
Jammer module 420 W DC 0 W 20 % 336 Wh Peak 420 W; thermal average lower
Cooling fans 40 W 0 W 50 % 80 Wh Ambient dependent
Total ≈ 1,166 Wh Illustrative four-hour mission

The audit produces two numbers: the energy required for the mission and the maximum simultaneous power. The energy sets the capacity; the power sets the cell count, the connector, the fuse and the DC-DC converter. A third number, the largest pulse current and its duration, sets the pack's internal resistance and voltage-sag limit.

Counter-UAS support load audit and duty cycle

Step 2 — Chemistry comparison

Property Sealed NiMH Li-ion (NMC/LFP) LiFePO4 VRLA lead-acid
Nominal cell voltage 1.2 V 3.6–3.7 V (NMC), 3.2 V (LFP) 3.2 V 2.0 V
Pack specific energy (planning) 70–100 Wh/kg 150–250 Wh/kg 90–140 Wh/kg 30–45 Wh/kg
Cycle life to 80 % 500–1,000 500–1,500 2,000–5,000 200–500
Pulse capability 3–8 C short pulse 5–20 C with BMS 5–15 C 3–8 C but large mass
Temperature range −20 to +60 °C, capacity derated cold −20 to +60 °C with BMS limits −20 to +60 °C −15 to +50 °C
Transport UN 3496; no UN 38.3 summary UN 3480/3481; UN 38.3 summary UN 3480/3481; UN 38.3 summary UN 2794 or non-regulated
Abuse tolerance High; tolerant of overcharge and over-discharge Moderate; BMS required High; BMS required Moderate; ventilation required
Cost per cycle Low to moderate Moderate Moderate to high Low but heavy

The comparison is not a ranking. A man-portable tactical detector should use lithium because mass is decisive. A fixed ground cart can use NiMH because mass is not decisive, the cycle count is high, the charge profile is simple and the transport route is easier. A remote solar node may prefer LiFePO4 for cycle life, or NiMH for tolerance of trickle charge and low-temperature robustness. The correct choice depends on the weighting, not on a universal "best chemistry" claim.

Step 3 — Voltage architecture and cell count

NiMH cells are 1.2 V nominal, about 1.45 V at full charge and about 1.0 V at end of discharge under moderate load. A 20S string is 24 V nominal, 29 V full and 20 V empty; a 10S string is 12 V nominal, 14.5 V full and 10 V empty. The system's input window, not the nominal voltage, decides the cell count.

System bus NiMH cell count Nominal Full charge End of discharge Typical use
12 V 10S 12.0 V 14.5 V 10.0 V Small C2, test bench, remote node
24 V 20S 24.0 V 29.0 V 20.0 V Ground cart, vehicle buffer, training set
28 V 24S 28.8 V 34.8 V 24.0 V Military 28 V bus, legacy equipment
48 V 40S 48.0 V 58.0 V 40.0 V Fixed-site buffer, high-power test bench

The full-charge voltage is the number that destroys converters. A 24 V bus that expects 24 V nominal may see 29 V from a fully charged 20S NiMH string; the DC-DC input must accept that, or the pack must be charged to a lower voltage. The end-of-discharge voltage is the number that causes brown-outs; the load must either accept 20 V or the low-voltage disconnect must trip before the load misbehaves.

Step 4 — Capacity arithmetic

Start with the average current, not the average power. For a 24 V bus, 293 W average is about 12.2 A. For a four-hour mission, the raw capacity is 48.8 Ah. Apply the derating stack to obtain the nameplate capacity:

Cnameplate = (Iavg × t) / (ktemp × kDoD × kEOL × krate × kwiring)

Factor Example value Why it applies
Temperature 0.80 Capacity at −20 °C is lower than at 25 °C; use the coldest expected operating point
Depth of discharge 0.90 Do not plan to 100 % DoD if cycle life matters
End of life 0.85 Capacity at end of specified life, not beginning
Discharge rate 0.95 Higher rate reduces usable capacity
Wiring and connector loss 0.97 Voltage drop and contact resistance
Product ≈ 0.60 48.8 Ah raw → about 81 Ah nameplate

An 81 Ah nameplate requirement is large for a single 24 V NiMH pack; it may be better to use two 40 Ah packs in parallel, or to reduce the mission time, or to move the jammer to a separate pack. The arithmetic does not decide the architecture; it exposes the trade-off. A pack that looks adequate at 25 °C and 100 % DoD may deliver only 60 % of its nameplate in the real environment.

Step 5 — Pulse current and voltage sag

The pulse load is a separate design case. A 420 W jammer at 24 V draws about 17.5 A; a 1 kW pulse draws about 42 A. A 20S NiMH pack with 40 Ah cells may have an internal resistance of 20–40 mΩ including wiring, so a 42 A pulse produces a 0.8–1.7 V sag. That is tolerable on a 24 V bus if the amplifier's input range is 20–30 V; it is not tolerable if the amplifier cuts out at 22 V.

Pulse current Assumed pack resistance Voltage sag Remaining bus voltage from 24 V Consequence
20 A 30 mΩ 0.6 V 23.4 V Usually acceptable
40 A 30 mΩ 1.2 V 22.8 V Check amplifier cut-off
60 A 30 mΩ 1.8 V 22.2 V May trip a 22 V cut-off
100 A 30 mΩ 3.0 V 21.0 V Requires shorter pulse or lower resistance

The table is illustrative; the actual resistance depends on cell size, tab design, wiring and connector. The design response is not to add capacity but to reduce resistance: larger cells, shorter cables, heavier lugs, a connector with a lower contact resistance, and a capacitor bank at the amplifier input. A capacitor bank can supply the microsecond and millisecond pulse; the battery supplies the millisecond-to-second pulse; the converter supplies the average.

Step 6 — Charging, protection and enclosure

Subsystem Requirement Why it matters
Charge method Constant current 0.1–0.3 C, −ΔV termination, temperature cut-off NiMH needs a proper termination; timer-only charging risks overcharge
Balance String matching and periodic equalisation Weak cells in a long string limit capacity and accelerate ageing
Low-voltage disconnect Latching at 0.9–1.0 V per cell Prevents cell reversal and permanent damage
Overcurrent protection Fuse or breaker sized for pulse, not average A 40 A continuous pack may see 100 A pulses
Reverse polarity Series MOSFET or ideal diode Field wiring errors are common
Temperature sensing Thermistor per string, charger and load cut-off Charge and discharge limits are temperature-dependent
Enclosure IP54 for sheltered; IP65/67 for exposed Dust, rain and wash-down are normal in field use
Mechanical Vibration, shock and handling drop MIL-STD-810H methods apply if the platform invokes them

Worked configurations

Configuration Electrical Energy Continuous / pulse Typical use
Man-portable training pack 10S 8 Ah, 12 V 96 Wh 8 A / 24 A Training detector, test set, remote sensor
Ground-support cart 20S 40 Ah, 24 V 960 Wh 30 A / 100 A C2, chargers, test bench, short jammer bursts
Vehicle buffer 20S 20 Ah, 24 V 480 Wh 20 A / 60 A Engine-off C2 and ride-through
Fixed-site buffer 40S 100 Ah, 48 V 4.8 kWh 50 A / 150 A Generator start, UPS ride-through, test bench
NiMH cell string and derating stack

Six sizing mistakes that show up in real RFQs

Mistake What it looks like Consequence Correct approach
Using RF output as DC input "100 W jammer, so 100 W load" Pack is undersized by a factor of three or more Divide RF power by amplifier efficiency; add driver and cooling
Sizing from average only "293 W average, so 300 W pack" Pulse collapses the bus and resets the C2 Check pulse current and voltage sag separately
Ignoring temperature Using 25 °C capacity at −20 °C Mission time falls by 20–40 % Apply the cold derating factor and specify a heater if needed
Ignoring end of life Using beginning-of-life capacity Pack fails the mission before the warranty ends Apply the EOL factor, typically 0.85
Charging with a timer only "8 h at 0.1 C is fine" Overcharge, heat, shortened life Use −ΔV and temperature cut-off; verify with a test
Testing cells, not the pack Cell report only Fuse, connector or enclosure fails in service Qualify the complete pack configuration

Procurement checklist

  • Name the mission and the environment: four hours at 293 W average, −20 to +55 °C, IP54, vehicle transport.
  • Name the pulse: 1 kW for 10 s, once per minute, with a minimum bus voltage of 22 V.
  • Name the charge source: 28 V vehicle, 24 V generator, or solar; state the available current and the recharge time.
  • Name the chemistry and the standard: sealed NiMH, IEC 61951-2, IEC 62133-1, UN 3496.
  • Name the interface: connector type, pinout, thermistor curve, communication protocol if any.
  • Name the documentation: test report, cell traceability, capacity at temperature, cycle-life data, transport paperwork.

Frequently asked questions

How do I convert watt-hours to Ah for a NiMH pack?

Divide the watt-hours by the nominal voltage. A 960 Wh pack at 24 V nominal is 40 Ah. Then apply the derating stack; the usable energy is lower than the nameplate, especially at low temperature and end of life.

Can I use a 20S NiMH pack on a 24 V system?

Only if the system accepts the full-charge voltage of about 29 V and the end-of-discharge voltage of about 20 V. The nominal 24 V label is not the operating window. Check the DC-DC converter and the load's cut-off thresholds.

Is NiMH a good choice for a man-portable counter-UAS detector?

Usually not for the primary pack. A dismounted operator needs the highest energy density available, and lithium-ion delivers 150–250 Wh/kg versus 70–100 Wh/kg for NiMH. NiMH is better suited to training, ground support and legacy equipment where mass is less critical.

What causes a NiMH pack to fail early in this application?

Overcharge without a proper termination, cell reversal from repeated deep discharge, high-temperature storage, and a weak cell in a long string. A charger with −ΔV and temperature cut-off, a latching low-voltage disconnect and string matching address most of these failure modes.

How much pulse current can a NiMH pack supply?

It depends on the cell, the pack resistance and the acceptable voltage sag. A well-built pack can supply 3–8 C for short pulses, but the datasheet must state the current, duration and sag. Do not assume that a 40 Ah pack can supply 100 A indefinitely.

Sources

IEC 61951-2:2017 + A1:2022, Secondary cells and batteries containing alkaline or other non-acid electrolytes — Secondary sealed cells and batteries for portable applications — Part 2: Nickel-metal hydride; IEC 62133-1:2017, Safety requirements for portable sealed secondary cells and batteries — Part 1: Nickel systems; IEC 60529, Degrees of protection provided by enclosures (IP Code); MIL-STD-810H, Environmental Engineering Considerations and Laboratory Tests; MIL-STD-461G, Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment; UN Manual of Tests and Criteria, UN 3496; IATA Dangerous Goods Regulations, Packing Instruction A199. All numeric examples are illustrative planning calculations, not measurements.

Next in this series

Paper C — Testing and certifying those packs: IEC 61951-2 cell performance, IEC 62133-1 safety tests, IEC 60529 ingress, MIL-STD-810H environmental, MIL-STD-461G EMC, abuse testing and the UN 3496 transport route.

Weijiang Power — sealed NiMH cells and packs for industrial support equipment.
OEM and custom configurations, with honest chemistry boundaries. Visit our product range or browse the full technical series.

Lastest News
Unlock the power of lithium batteries for lasting performance in handheld vacuum cleaners. Weijiang Li-on Battery leads the charge in innovation.
READ MORE
A NiMH battery pack is a collection of individual NiMH batteries connected in series or parallel to create a higher voltage or capacity battery.
READ MORE
REQUEST MORE DETAILS
Please fill out the form below and click the button to request more information about
Name*
Whatsapp/Phone
Email*
Message*
Professional battery factory, support OEM & ODM customization.
REQUEST MORE DETAILS
Please fill out the form below and click the button to request more information about
Company Name*
Email Address*
WhatsApp / Phone*
Message & Requirements*

Buyer fact sheet

Weijiang Power at a glance

Legal entityShenzhen Weijiang Battery Co., Ltd., trading as Weijiang Power
Founded2010, 16 years of NiMH battery manufacturing
FactoryHuizhou Shenzhou Super Power Technology Co., Ltd., Zhongkai High-tech Zone, Huizhou, Guangdong; 12,000 m2, 4 workshops
Capacity200,000 NiMH cells per day; 200+ staff including 11-20 R&D engineers and 10 QC inspectors
Product rangeNiMH cells A, AA, AAA, SC, C, D, 9V, F, Sub-C, 4/5AA, 2/3A; custom NiMH packs; chargers; button and alkaline cells
CertificationsCE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001:2015, ISO 14001, IATF 16949, IEC 62321, MSDS, UL, IEC 62133; 16 patents; UN38.3 applies only to lithium packs
Markets60+ countries, focus on Europe and the United States
Order termsNo strict MOQ on standard stock; OEM samples 7-15 days; standard production 7-12 days; custom packs 15-25 days
Medical NiMHMedical NiMH battery page

Quick answers for buyers

Who is Weijiang Power?
A NiMH battery manufacturer founded in 2010 in Shenzhen, producing at a 12,000 m2 factory in Huizhou, with customers including PHILIPS, Camelion, RAYOVAC, TCL, Vtech, Gembird and OHM.

What can Weijiang Power supply?
Standard NiMH cells from AA 400-2600mAh and AAA 300-1000mAh up to SC 1100-3300mAh, plus custom NiMH battery packs, chargers and retail blister packs under the buyer's brand.

Which certificates are available for EU and US buyers?
CE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001, ISO 14001, IATF 16949, IEC 62321, MSDS, UL and IEC 62133, with 16 patents; UN38.3 applies only to lithium packs.

What is the minimum order and lead time?
Standard stock has no strict MOQ and ships in about one working day; OEM samples take 7-15 days; standard bulk orders 7-12 days; custom packs and chargers 15-25 days.

How do I get a sample or a quote?
Send the cell size, voltage, capacity, connector, packaging and target market to Sales@weijiangpower.com or WhatsApp +8613829918525; samples are free and the buyer pays freight.

Deeper reading: NiMH battery sourcing guide for EU and US buyers · EU battery regulation and NiMH compliance guide · Certification checklist · Full FAQ

Language versions: Deutsch · Français · Español

Last reviewed: 20 November 2026. Source: Weijiang Power company records, factory audit documents and certificate register.