Nov.2026 22
Views: 39
Powering Cordless Power Tools: Tool Classes, Load Profiles, Voltage Architectures and the NiMH Support Role
Introduction
Paper A: how drills, impact drivers, saws, grinders and garden tools load a battery; why trigger, stall and thermal peaks differ from nameplate watts; how 12 V, 18 V and 36 V packs are built; and where sealed NiMH is still defensible in the cordless tool ecosystem.
Details

Cordless power tool battery load profiles, tool classes, voltage architectures and the NiMH support role

A cordless power tool does not draw a steady current. It sleeps, then wakes when the trigger is pulled, accelerates a motor and a gearbox, cuts or drills into a load, and returns to sleep. The battery sees a low standby drain, a short inrush pulse, a working current that rises with torque, and occasional stall or jam currents that can be several times the normal load. The nameplate voltage and amp-hour rating describe only part of that duty. This paper separates the tool families, explains what the battery actually sees, and states where a sealed nickel-metal-hydride (NiMH) pack remains a defensible choice in a market now dominated by lithium-ion.

Key facts at a glance

  • An "18 V" tool is not a 18.0 V battery. A 15-cell NiMH pack is nominally 18.0 V at 1.2 V per cell, about 21 V when fully charged, and around 15 V at a conservative 1.0 V per cell cutoff. The tool's motor and electronics must accept that whole window.
  • The trigger current is not the working current. Motor inrush lasts milliseconds; drilling or cutting current lasts seconds to minutes; stall current can exceed 100 A in a small tool but is limited by the pack, fuse, switch and motor resistance.
  • Torque and current rise together. A brushed or brushless motor produces torque roughly proportional to current, so a hard cut in dense wood or a bind in a drill bit is an electrical event as much as a mechanical one.
  • Thermal design follows RMS current, not average current. A tool that averages 8 A but repeatedly pulses to 40 A heats the cell, switch and connector as if the current were much higher than the arithmetic mean.
  • NiMH remains defensible in low-cost, legacy, wide-temperature and safety-sensitive niches. It is not the right chemistry for a premium compact 18 V tool where energy density, weight and fuel gauging decide the sale.

The five tool families and their electrical personalities

Power tools are often marketed by voltage, but the electrical load is set by the mechanism. A drill spends most of its time spinning freely and only briefly cutting; a grinder runs at high speed under a continuous abrasive load; a reciprocating saw has a mechanical stroke and a high instantaneous blade load; a blower is a continuous air load. The table below groups the common families by what the battery sees.

Tool family Typical examples Electrical character Dominant stress
Drilling and fastening Drill-driver, impact driver, impact wrench, hammer drill Short high-torque pulses; trigger inrush; idle between fasteners Peak current, switch and connector heating, clutch slip
Sawing Circular saw, reciprocating saw, jigsaw, chain saw High working current under load; jam or kickback peaks Stall current, blade bind, thermal pulse
Grinding and sanding Angle grinder, random orbital sander, detail sander Continuous medium-to-high current; speed droop under pressure Continuous thermal load, dust ingress, vibration
Garden machinery Hedge trimmer, string trimmer, leaf blower, lawn mower Long continuous runs; high airflow or cutting load Runtime, motor heating, outdoor temperature and moisture
Specialty tools Rotary hammer, caulking gun, drain auger, concrete vibrator Very high short pulses or slow high-torque output Peak current, gearbox load, duty cycle

The same 18 V pack may be sold across all five families. That does not mean the same cells or the same protection are appropriate. A compact drill pack optimised for weight will heat faster in a grinder; a garden pack optimised for runtime will be too heavy for overhead drilling. The pack must be matched to the tool family, not only to the connector.

Voltage classes and pack topology

Cordless tool voltage is a nominal cell count. NiMH cells are 1.2 V nominal, so 10 cells make a 12 V pack, 15 cells make an 18 V pack, 20 cells make a 24 V pack, and 30 cells make a 36 V pack. Lithium packs use a different cell count and a different nominal voltage per cell, which is why an "18 V" lithium pack and an "18 V" NiMH pack are not electrically interchangeable even when the connector looks similar.

Nominal class NiMH series count Nominal voltage Typical full-charge voltage Typical cutoff Common tools
12 V 10S 12.0 V ≈ 14.0–14.5 V ≈ 10.0 V Compact drills, drivers, detail sanders
18 V 15S 18.0 V ≈ 21.0–21.8 V ≈ 15.0 V Drills, impact drivers, saws, grinders, blowers
24 V 20S 24.0 V ≈ 28.0–29.0 V ≈ 20.0 V Heavy drills, rotary hammers, garden tools
36 V 30S 36.0 V ≈ 42.0–43.5 V ≈ 30.0 V Lawn mowers, chainsaws, heavy stationary tools

The full-charge voltage is not a marketing number. A 15S NiMH pack taken to 1.45 V per cell reaches 21.75 V, and a charger that misses termination can push individual cells higher. The tool's switch, motor controller and any electronic speed control must be rated for the highest voltage the pack can deliver, not only the nominal 18 V. The cutoff must also be set with cell behaviour in mind: a 1.0 V per cell cutoff protects the weakest cell, while a 0.9 V per cell cutoff gains runtime at the cost of cycle life and risk of cell reversal.

What the battery sees: standby, inrush, work and stall

A tool's current profile has four phases. The pack, fuse, switch and connector must survive all four. A cell datasheet that lists only a continuous 0.2 C capacity test does not describe any of them.

Phase Duration Typical current What it stresses Design response
Standby / sleep Hours to weeks Microamps to a few milliamps Self-discharge, electronics quiescent drain Low-self-discharge cells; mechanical or electronic disconnect
Trigger inrush Milliseconds 2–5× running current Switch contacts, connector, fuse, DC link Pre-charge or soft-start; fuse with appropriate I²t; connector margin
Working load Seconds to minutes 5–30 A for an 18 V hand tool Cell heating, voltage sag, motor efficiency High-rate cells; matched internal resistance; thermal path
Stall or jam Milliseconds to seconds 50–150 A or more Cell, switch, fuse, motor commutator Electronic current limit; mechanical clutch; fuse; pack PTC

The numbers are illustrative because tool and pack designs vary widely. The important point is the ratio: a tool that draws 10 A while drilling may draw 50 A at stall, and a pack that supplies 10 A without complaint may sag enough at 50 A to reset the tool's electronics or trip protection. The battery is not a reservoir with one current rating; it is a network of cells, welds, wires, connectors and protection devices, each with its own limit.

Average current by cordless power tool class

Torque, current and voltage sag: the arithmetic

For a permanent-magnet DC motor, torque is approximately proportional to armature current, and back-EMF is approximately proportional to speed. At a given supply voltage, the current rises as the mechanical load slows the motor. A simplified relationship is:

T ≈ Kt × I     and     Vterminal ≈ VOCV − I × Rpack

Where Kt is the motor torque constant, VOCV is the pack open-circuit voltage, and Rpack is the pack resistance including cells, welds, wiring, connector and protection. The table below shows how a 15S pack with 90 mΩ total resistance behaves at different currents. The values are illustrative but the arithmetic is real.

Pack current Open-circuit voltage Voltage sag at 90 mΩ Terminal voltage Approximate resistive loss
5 A 19.5 V 0.45 V 19.05 V 2.3 W
10 A 19.5 V 0.90 V 18.60 V 9.0 W
20 A 19.5 V 1.80 V 17.70 V 36 W
30 A 19.5 V 2.70 V 16.80 V 81 W
50 A 19.5 V 4.50 V 15.00 V 225 W

At 50 A the pack loses 225 W as heat inside cells, welds and connectors. That heat is the reason a high-rate pack cannot be judged only by its amp-hour label. A 3.0 Ah pack at 50 A is running at nearly 17 C; the cells may survive short pulses, but the pack's thermal path and the connector's contact resistance become the limiting components. The voltage sag also reduces the motor's speed and torque, which is why a "18 V" tool feels weaker on a partially discharged or cold pack.

The same arithmetic explains why a 2.0 Ah pack and a 4.0 Ah pack can have the same voltage but different sag. If the 4.0 Ah pack uses cells with lower internal resistance, it will hold voltage better under load. If it simply uses more capacity in the same cell format, it may have similar resistance per cell and no better peak performance. Amp-hour is energy; internal resistance is power capability. Both matter.

Duty cycle, RMS current and thermal design

A tool's workday is not a continuous current test. A installer may drive twenty screws in a minute, each for two seconds, then set the tool down for a minute. A carpenter may run a circular saw for thirty seconds, then measure and reposition for two minutes. A landscaper may run a blower continuously for twenty minutes. The battery and motor heat according to the RMS current over the thermal time constant, not the simple average.

Task Work pulse Rest between pulses Approximate duty Thermal character
Assembly driving 1–3 s 5–20 s 5–30 % Many short pulses; connector and switch heat
Drilling metal 10–60 s 10–60 s 20–50 % Medium continuous load; coolant and chip clearing
Circular sawing 10–60 s 10–120 s 20–60 % High current; blade bind possible
Angle grinding 1–10 min 1–5 min 30–80 % Continuous thermal load; dust ingress
Leaf blowing 10–30 min 0–5 min 80–100 % Continuous high airflow load; motor and pack heat

A pack sized from average current will overheat in the grinder or blower case. A pack sized from the highest pulse will be unnecessarily heavy for the assembly case. The correct method is to calculate both the energy needed for the task and the RMS current over the thermal window, then choose a cell and pack that satisfy both. Paper B sets out that calculation.

Where sealed NiMH is still defensible

The cordless tool market moved to lithium-ion for good reasons: more energy per kilogram, a flat discharge curve, accurate state of charge, fast charging and compact packs. A claim that NiMH is the best chemistry for a modern premium drill would be false. But the market is not monolithic. There are real segments where NiMH remains technically and commercially defensible.

Application Why NiMH fits What to specify
Value-tier consumer tools Low pack cost, mature chargers, simple electronics, tolerance of overcharge 12 V or 18 V, 1.5–3.0 Ah, 10–20 A continuous, 40–60 A pulse
Legacy tool replacement Original pack was NiMH; a drop-in replacement avoids tool and charger requalification Match cell count, connector, thermistor curve and charge profile
Safety-sensitive or abusive use Nickel chemistry is tolerant of over-discharge and mechanical abuse relative to lithium IEC 62133-1, PTC, fuse, robust enclosure, 1.0 V/cell cutoff
Wide-temperature outdoor tools NiMH can discharge below 0 °C and tolerate high ambient storage better than some lithium packs −20 °C capacity data, 0–45 °C charge limit, thermal derating
Educational, rental and shared fleets Low replacement cost, simple storage, no fuel gauge to calibrate 18 V 2.0–3.0 Ah, 500+ cycles, mechanical keying, clear labelling
Test benches and charger buffers Stable low-cost DC source for tool repair and production testing 12/18/24 V, current limit, e-stop, thermistor, IP54

The table is a commercial map, not a claim of superiority. The value-tier segment competes on shelf price and replacement revenue. The legacy segment competes on fit and availability. The safety-sensitive segment competes on certification and abuse tolerance. A NiMH pack can win those segments without pretending to win the premium compact segment.

Where NiMH is not defensible

  • Premium compact 18 V tools. A 3.0 Ah NiMH 18 V pack stores about 54 Wh and weighs about 1 kg; a comparable lithium pack stores more energy in less mass. The user feels the difference immediately.
  • High-power continuous grinding or heavy cutting. NiMH can supply high current, but the voltage sag and thermal load at 20–30 C continuous are worse than a lithium pack of the same mass.
  • Fuel-gauge and battery-management features. NiMH state of charge is harder to estimate from voltage because the discharge curve is relatively flat and temperature-dependent. A simple LED bar is honest; a precise percentage is not.
  • Fast-charge ecosystems. A 30-minute charger is a lithium-oriented product. NiMH fast charging is possible, but termination by −ΔV and temperature rise is less forgiving, and cell matching becomes critical.
  • Claims that NiMH "replaces lithium" in all cordless tools. The honest claim is narrower: NiMH serves specific value, legacy, safety and temperature segments, and it does so with a different set of trade-offs.
Cordless tool voltage classes and pack voltage window

Chemistry comparison at pack level

Property Sealed NiMH Lithium-ion What it means for a tool
Nominal cell voltage 1.2 V 3.6–3.7 V NiMH needs more cells in series for the same pack voltage
Energy density ≈ 50–80 Wh/kg pack ≈ 120–200 Wh/kg pack NiMH packs are heavier for the same energy
Discharge curve Relatively flat, then a knee Flat plateau, then a knee Both are usable; NiMH gauge is less precise
High-rate capability 10–20 C with high-rate cells 20–40 C with power cells Both can pulse; lithium holds voltage better
Overcharge tolerance Good with correct termination and trickle Requires strict protection NiMH is more forgiving in low-cost chargers
Transport UN 3496 sea; A199 air "not restricted" UN 38.3, UN 3480/3481 NiMH avoids lithium air-cargo paperwork

The comparison is deliberately at pack level, because a cell comparison can mislead. A high-rate NiMH cell may match a lithium cell's pulse current in the short term, but the pack-level energy, mass and voltage sag still differ. The customer buys a pack, not a cell.

Standards anchors for a cordless tool pack

Standard Scope Why it matters
IEC 61951-2:2017 + A1:2022 Sealed NiMH cell performance and cycle life Capacity, high-rate discharge, charge retention and endurance
IEC 62133-1:2017 / 2026 Safety of portable sealed nickel cells and batteries Abuse, thermal, mechanical and electrical safety
IEC 62841-1:2014 + AMD1:2025 General safety of motor-operated tools; Annex K covers battery tools and packs Tool-level electrical, thermal and mechanical safety
IEC 62841-2-1 / -2-2 / -2-3 / -2-5 / -2-11 Particular requirements for drills, impact tools, grinders, saws Tool-family-specific tests and markings
IEC 60335-2-29 Safety of battery chargers Charger thermal, electrical and abnormal-operation safety
CISPR 14-1 / EN 55014-1 and CISPR 14-2 / EN 55014-2 EMC emission and immunity for household appliances and electric tools Motor brush noise, charger conducted emissions, immunity
IEC 60529 IP ingress protection IP54 for general; IP65 for outdoor or dusty sites
UN 3496 / IATA A199 NiMH transport by sea and air Sea IMDG entry; air shipment "not restricted" with A199 conditions

The standards list is not a claim that every pack needs every standard. A consumer 12 V drill pack may need IEC 62133-1, IEC 62841-1 Annex K and the relevant EMC standard. A garden tool pack may add IP65 and UV/moisture testing. A pack shipped by air needs the A199 packing conditions and the correct air waybill wording. Over-specification raises cost; under-specification blocks market access.

What to ask before quoting a cordless tool pack

Question Why it changes the pack Typical answer
Which tool family and model? Sets peak current, duty cycle and connector 18 V drill-driver, impact driver or grinder
What is the stall or jam current? Sets fuse, PTC, switch and connector rating 40–100 A for a hand tool; higher for garden tools
What runtime is required? Sets cell capacity and pack mass 30–60 min mixed use; 15–30 min continuous heavy use
What is the charge window? Sets charger, termination and cell matching 1–3 h; −ΔV plus temperature cutoff
What are the storage and use temperatures? Sets capacity derating and charge limits −20 to +50 °C outdoor; 0–40 °C indoor
Which certifications and markets? Sets test plan and documentation EU CE, UKCA, US, Japan, Korea or a subset

A quote that starts with "18 V 3.0 Ah" is not a specification. The useful quote starts with the tool, the load, the duty, the connector, the charger and the market. The rest follows.

Bottom line

Cordless power tools are a high-rate, pulsed, thermally demanding application. The battery must supply inrush, working current and stall current without excessive sag, and it must survive repeated thermal cycles in a dirty, vibrating enclosure. Lithium-ion wins the premium compact segment on energy density and management features. Sealed NiMH remains a credible choice in value-tier tools, legacy replacement packs, safety-sensitive and wide-temperature applications, and test-bench or charger-buffer roles. The engineering task is not to argue chemistry in general; it is to match the cell, pack, protection and charger to the specific tool and duty.

Lastest News
Unlock the power of lithium batteries for lasting performance in handheld vacuum cleaners. Weijiang Li-on Battery leads the charge in innovation.
READ MORE
A NiMH battery pack is a collection of individual NiMH batteries connected in series or parallel to create a higher voltage or capacity battery.
READ MORE
REQUEST MORE DETAILS
Please fill out the form below and click the button to request more information about
Name*
Whatsapp/Phone
Email*
Message*
Professional battery factory, support OEM & ODM customization.
REQUEST MORE DETAILS
Please fill out the form below and click the button to request more information about
Company Name*
Email Address*
WhatsApp / Phone*
Message & Requirements*

Buyer fact sheet

Weijiang Power at a glance

Legal entityShenzhen Weijiang Battery Co., Ltd., trading as Weijiang Power
Founded2010, 16 years of NiMH battery manufacturing
FactoryHuizhou Shenzhou Super Power Technology Co., Ltd., Zhongkai High-tech Zone, Huizhou, Guangdong; 12,000 m2, 4 workshops
Capacity200,000 NiMH cells per day; 200+ staff including 11-20 R&D engineers and 10 QC inspectors
Product rangeNiMH cells A, AA, AAA, SC, C, D, 9V, F, Sub-C, 4/5AA, 2/3A; custom NiMH packs; chargers; button and alkaline cells
CertificationsCE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001:2015, ISO 14001, IATF 16949, IEC 62321, MSDS, UL, IEC 62133; 16 patents; UN38.3 applies only to lithium packs
Markets60+ countries, focus on Europe and the United States
Order termsNo strict MOQ on standard stock; OEM samples 7-15 days; standard production 7-12 days; custom packs 15-25 days
Medical NiMHMedical NiMH battery page

Quick answers for buyers

Who is Weijiang Power?
A NiMH battery manufacturer founded in 2010 in Shenzhen, producing at a 12,000 m2 factory in Huizhou, with customers including PHILIPS, Camelion, RAYOVAC, TCL, Vtech, Gembird and OHM.

What can Weijiang Power supply?
Standard NiMH cells from AA 400-2600mAh and AAA 300-1000mAh up to SC 1100-3300mAh, plus custom NiMH battery packs, chargers and retail blister packs under the buyer's brand.

Which certificates are available for EU and US buyers?
CE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001, ISO 14001, IATF 16949, IEC 62321, MSDS, UL and IEC 62133, with 16 patents; UN38.3 applies only to lithium packs.

What is the minimum order and lead time?
Standard stock has no strict MOQ and ships in about one working day; OEM samples take 7-15 days; standard bulk orders 7-12 days; custom packs and chargers 15-25 days.

How do I get a sample or a quote?
Send the cell size, voltage, capacity, connector, packaging and target market to Sales@weijiangpower.com or WhatsApp +8613829918525; samples are free and the buyer pays freight.

Deeper reading: NiMH battery sourcing guide for EU and US buyers · EU battery regulation and NiMH compliance guide · Certification checklist · Full FAQ

Language versions: Deutsch · Français · Español

Last reviewed: 20 November 2026. Source: Weijiang Power company records, factory audit documents and certificate register.