
This is Paper A of the C04 note on military training and target drone equipment, and it answers the first question an OEM battery engineer has to settle before any cell or pack is sized: how is this equipment actually powered, and what kind of load does it present? The answer is not a single number. A training range runs several very different machines at once - full-size jet targets that are turbine aircraft, small electric target drones that need high-rate lithium, ground pop-up targets driven by short motor pulses, laser-engagement electronics that run for long sessions at low current, and the ground control stations that tie them together. This paper maps each machine to its power source and load profile, explains why sealed nickel-metal hydride is the correct chemistry in some places and honestly the wrong one in others, and sets up the selection and sizing work in Papers B and C. Every current and runtime figure that is not a published specification is labelled illustrative, and the binding values for a real project remain the device manual and the agreed pack drawing.
Key fact 1. Aerial targets are not one product class, and the power source changes with the tier. Full-scale aerial targets such as the QF-16 and QF-4 are retired jet fighters flown unmanned and driven by turbofan or turbojet engines, so batteries support only the avionics and control electronics. Sub-scale jet and piston targets such as the Banshee and the D210 use small engines, while the smallest electric target drones and multirotors fly on high-rate lithium-polymer or lithium-ion cells. There is no battery propulsion role on a full-size jet target.
Key fact 2. Sealed NiMH is honestly not the flight battery for an electric target drone. Flight endurance is weight-limited, and a LiPo cell offers roughly 150-210 Wh/kg and discharge rates commonly stated from 30 C up to about 150 C, against roughly 60-120 Wh/kg and a practical 10-20 C ceiling for NiMH. The heavier nickel cell and its lower discharge rate make it unsuitable for high-performance electric propulsion, and presenting it as a target-drone flight battery would be the wrong claim.
Key fact 3. The realistic NiMH role is on the ground, in repeated-use equipment. Pop-up, rising and swing targets use a brushless motor to move a heavy plate through short 0.8-1.5 second pulses, and they are fielded as fleets with separable 24 V battery boxes and multi-bay chargers. A sealed NiMH pack can replace the legacy lead-acid box here with no liquid, no routine maintenance, a flat voltage and little loss under load, while tolerating the handling and repeated cycling of a busy range.
Key fact 4. Force-on-force training electronics are a low-current, long-session load. The MILES 2000 requirement calls for 100 hours without power-source replacement, and the laser safety rules follow 21 CFR 1040 with MIL-STD-1425 as the fallback design standard. Individual laser targets, engagement sensors and weapon simulators draw small currents and turn over on rechargeable cells, which is the same rechargeable logistics logic as the ground targets rather than a high-power propulsion problem.
Key fact 5. The whole case rests on reuse rather than expendability. Training, garrison and depot equipment comes back after every exercise and is recharged on a defined schedule, so a sealed NiMH pack removes the cost and waste of disposable cells and the maintenance of lead-acid. This is distinct from the frontline, where extreme-cold and single-use missions reach for primary lithium, and NiMH is not claimed as the better choice for those coldest combat tasks.
The first principle is to separate the machines by what moves and how. A useful map divides the range into four groups: aerial targets that fly, ground targets that move a plate, wearable or portable laser-engagement electronics, and the fixed or transportable control and support equipment. Each group has a different duty cycle, a different acceptable weight and a different chemistry, and treating them as one battery problem is the most common source of an overstated claim. The table below fixes the power source for each group before any sizing is attempted.
| Equipment group | Typical examples | Power source | Load character |
|---|---|---|---|
| Full-scale aerial targets | QF-16, QF-4 | Turbofan / turbojet; battery for avionics only | Turbine propulsion, not battery |
| Sub-scale targets | Banshee, D210 | Small jet / piston engine | Engine propulsion; small electronics |
| Electric target drones | T.H.R.E.A.T., target multirotors | High-rate LiPo / Li-ion | High-current motor, weight-limited |
| Ground moving targets | Pop-up / rising / swing targets | 24 V battery box (legacy lead-acid) | Short motor pulses, long idle |
| Laser-engagement electronics | MILES, weapon simulators, sensors | Small rechargeable cells | Low current, long session |
| Control and support | Ground control station, telemetry | Mains / PoE with backup battery | Standby with short ride-through |
The full-scale tier is an aircraft conversion rather than a new drone. The QF-16 is a remotely flown F-16 about 49.4 feet long with a 31 foot wingspan and a maximum takeoff weight near 37,500 pounds, capable of about Mach 1.47 on its Pratt & Whitney F100 augmented turbofan; the older QF-4 is a twin-turbojet aircraft with a maximum takeoff weight around 28 tonnes and a top speed near 2,389 km/h. These machines can be flown manned or unmanned and carry a flight-termination system, but the propulsion is the jet engine. Onboard batteries keep the flight controls, telemetry and termination electronics alive, and they are sized for that avionics load rather than for any motive power.
The sub-scale tier trades size for cost and still uses engines. The Banshee family is roughly 2.84 m long with a 2.49 m wingspan and is used by more than forty nations to represent missiles and aircraft for surface-to-air and air-to-air training, while the jet-powered D210 has a 2.12 m wingspan and a 30 kg maximum takeoff weight. The smallest tier is where electric flight appears: target multirotors and fixed-wing sUAS use brushless motors ranging from little 107-150 W units up to around 2 kW total on a 1.3 kg class training drone, with flight times commonly between about ten and twenty-five minutes, and one target system is built around common 18650 lithium-ion cells rather than a proprietary pack.

An electric drone carries its battery into the air, so the two numbers that decide the chemistry are energy per unit mass and the discharge rate. A high-rate LiPo cell sits at roughly 150-210 Wh/kg and is commonly rated from about 30 C to 150 C, which lets it feed a motor that may demand many times the pack's nominal capacity in an hour. A sealed NiMH cell offers roughly 60-120 Wh/kg and a practical continuous rate near 10-20 C, so the same energy requires a heavier pack and the highest motor currents sit beyond its comfortable range. On a weight-limited airframe that combination is decisive, which is why the electric target tier is a lithium design and not a nickel one.
This is stated as a boundary rather than a weakness of NiMH in its proper place. The nickel chemistry is genuinely robust - it tolerates overcharge and handling, holds a flat 1.2 V discharge and contains no cadmium - but those virtues matter most in ground equipment that does not pay a flight-weight penalty. Where the equipment is a full-scale jet target the point is moot because the engine does the work, and where it is a small electric drone the honest engineering answer is lithium. Weijiang does not manufacture lithium-ion cells in any case; lithium work is pack assembly only and follows the lithium transport rules rather than the nickel path.
The ground target is where sealed NiMH has a defensible and well-matched role. A pop-up, rising or swing target uses a brushless motor to lift a plate that can weigh five kilograms or more, holds it visible for a set interval and lowers it again, all under wireless control from a central station or tablet that can manage many targets at ranges of two hundred metres and beyond. The motor is on only for the brief 0.8-1.5 second movement, after which the machine sits in a low-current idle with its detection and radio electronics awake, so the duty cycle is a repeating pattern of short high-load pulses separated by long quiet gaps rather than a steady draw.
The field specifications show why this is a rechargeable fleet product. A charged machine is rated for at least 800 and in some designs more than 1,800 pop-up cycles and eight or more hours of normal use, with one legacy requirement specifying a separable 24 V / 8 Ah sealed lead-acid box and a multi-bay base that can charge up to ten batteries at once. The battery box is deliberately separable with a charge or voltage display so crews can swap and turn the fleet around. A sealed NiMH pack built at the same 24 V class removes the liquid and maintenance of lead-acid, keeps a level voltage with little Peukert loss under the repeated pulses, and cycles roughly 500-1,000 times against about 200-500 for lead-acid, while the target machines themselves are rated across roughly minus 20 to 70 C and resist wind and rain.

Laser engagement systems shift the problem from mechanical power to endurance. The MILES 2000 operational requirement is explicit that a device should be capable of operating for 100 hours without power-source replacement, because a force-on-force exercise runs from squad to brigade level and the kit is worn on weapons, helmets and vehicles where frequent battery changes break the training. The same requirement fixes laser safety under 21 CFR 1040, with MIL-STD-1425 used as the design standard where the civilian rule cannot be met, and it asks for reduced power consumption and longer-life batteries specifically to lower the logistics burden.
The individual devices confirm the low-current character. Portable laser targets and hit sensors run on small cells in the few-hundred-milliampere-hour class and recharge over USB, weapon simulators and the older infrared targets use small lead-acid or lithium packs giving roughly fifteen hours, and accessory simulators such as a mine emulator run for many hours on a single charge. These are not high-rate loads; they are long, shallow discharges that turn over on a schedule, which is the same rechargeable logic as the ground targets and a natural fit for a small sealed nickel cell where the buyer wants a robust, not-restricted rechargeable rather than a disposable.
The control station and the telemetry that links the range together are usually mains or Power-over-Ethernet equipment, with a battery used only to survive a short power interruption rather than as the primary source. A modern ground station illustrates the scale: it draws as little as about seven watts in standby and carries a small backup battery that provides roughly forty-five minutes in gateway mode and thirty minutes in relay mode after a power loss, inside a sealed enclosure built for unattended operation. The stationary armor target uses a larger 12 V battery or an AC converter and reports position and maintenance status over the network. Here the battery is a ride-through and support device, and the value of a sealed, abuse-tolerant nickel pack is in unattended reliability and not-restricted handling rather than energy density.
When the machines are reduced to their electrical shape, the range presents three distinct profiles. The propulsion profile is a high-current, weight-limited motor on an electric drone, correctly served by high-rate lithium; the actuator profile is a short motor pulse repeated over a long idle on a ground target, well matched to a sealed NiMH pack; and the electronics profile is a low-current, long-session draw in laser and control equipment, served by small rechargeable cells. The design rule follows directly: match the chemistry to the profile and the duty cycle, and never carry a claim from one profile into another. A NiMH pack sized for an actuator or an electronics load is a defensible design, while the same pack offered as drone propulsion would be both heavier and under-rated for the currents the motor actually demands.
| Load profile | Where it appears | Correct chemistry |
|---|---|---|
| High-current, weight-limited | Electric target drone propulsion | High-rate LiPo / Li-ion |
| Short pulse, long idle | Ground pop-up / swing target actuator | Sealed NiMH (or lead-acid legacy) |
| Low current, long session | MILES electronics, sensors, GCS backup | Small rechargeable NiMH / lithium |
The scope is stated plainly rather than stretched across every machine on the range. Sealed NiMH is not offered as a target-drone flight battery, where high-rate lithium is the correct chemistry, and it has no propulsion role on a full-scale jet target. The genuine applications are the ground pop-up, rising and swing target actuator packs that replace lead-acid, the low-current laser-engagement electronics and accessories that turn over on a schedule, and the fixed-site controllers, telemetry and support backup where abuse tolerance and not-restricted shipping matter. All of these are repeated-use training, garrison and depot equipment that comes back and recharges, which is the condition under which the nickel chemistry pays off. At the frontline, where extreme cold and single-use missions dominate, the honest choice is primary lithium rather than a NiMH cell, and no claim is made that nickel outperforms it on those coldest tasks.
No. Full-scale aerial targets such as the QF-16 and QF-4 are converted jet fighters and their propulsion is a turbofan or turbojet engine, with the QF-16 reaching about Mach 1.47. Onboard batteries support the avionics, telemetry and flight-termination electronics only; they do not drive the aircraft. The smallest electric target drones are the ones that fly on batteries, and those use high-rate lithium.
Because flight endurance is weight-limited and the motor needs a high discharge rate. A LiPo cell offers roughly 150-210 Wh/kg and rates of about 30-150 C, while NiMH offers roughly 60-120 Wh/kg and a practical 10-20 C ceiling. The nickel pack would be heavier for the same energy and under-rated for the motor currents, so high-rate lithium is the honest flight choice; NiMH is better matched to ground equipment that pays no flight-weight penalty.
Its duty cycle and its fleet logistics. The motor runs only for short 0.8-1.5 second pulses to lift and lower a plate, with long low-current idle gaps, and the separable 24 V battery box is swapped and recharged on a multi-bay base that handles up to ten packs. A sealed NiMH pack replaces the legacy lead-acid box with no liquid or maintenance, a flat voltage and roughly 500-1,000 cycles, and it tolerates the repeated handling of a busy range.
The MILES 2000 requirement calls for 100 hours without power-source replacement, and individual laser targets and sensors are small low-current devices that recharge on a schedule. The laser safety rules follow 21 CFR 1040, with MIL-STD-1425 as the fallback design standard. These are long, shallow discharges rather than high-rate loads, which is why small rechargeable cells suit them.
Its honest scope is the repeated-use training, garrison and depot equipment that returns and recharges. Frontline extreme-cold and single-use missions are designed around primary lithium, and NiMH is not claimed to outperform it on the coldest tasks. The strength of sealed NiMH is in removing disposable waste and lead-acid maintenance across a reusable fleet, not in replacing frontline primary cells.
The equipment taxonomy and specifications draw on published military and manufacturer references covering the QF-16 and QF-4 full-scale targets, the Banshee and D210 sub-scale targets, electric target drones and their brushless motors, ground pop-up target machines and their separable battery boxes, and MILES 2000 and ground-control-station requirements. The chemistry ranges - roughly 150-210 Wh/kg and 30-150 C for high-rate lithium against 60-120 Wh/kg and 10-20 C for NiMH, and about 500-1,000 cycles for NiMH against 200-500 for lead-acid - are typical published values rather than measurements of a named product, and the actuator load levels in the figures are illustrative. Nickel cells and packs are qualified to IEC 61951-2 and IEC 62133-1 and ship under UN 3496 with the IATA A199 not-restricted air path, environmental qualification follows MIL-STD-810 and MIL-STD-461, and laser safety follows 21 CFR 1040 with MIL-STD-1425. No statistics have been invented.
Weijiang Power supplies sealed NiMH cells and assembled NiMH packs for the ground target actuators, laser-engagement electronics and range support equipment of military training programs, built at the 24 V and smaller classes to the device geometry with PTC and resettable-fuse protection. The cells are qualified to IEC 61951-2 and IEC 62133-1 and the packs ship under UN 3496 with the not-restricted air path under IATA A199. We do not present NiMH as a target-drone flight battery, and we do not manufacture lithium-ion cells; lithium work is pack assembly only. Send us your equipment type, nominal voltage, motor or electronics current, pulse timing and duty cycle, expected temperature and charging arrangement, and we will work through the chemistry match, cell count and pack design and support the evidence for your evaluation. See the Weijiang NiMH product range for standard pack formats, or contact our OEM team with the device specification and load profile.